Hello,

recently bought a DSL40CR-U a truly fine amplifier brialliant Marshall!

what does the "U" mean in a DSL40CR-U?   thanks Rod

i just want to find the full manual, but after i check all the web pages, i still couldn't find it. Help me please.

ciao a tutti,

ho appena acquistato un Marshall MG15 Gold, ma appena lo accendo (anche senza cavi collegati) si sente un fruscio di sottofondo. E' un difetto di fabbrica?

good morning I purchased a marshall code 50, I immediately updated the firmware to version 1.48, I performed all the possible procedures for connecting to the phone, when I press rev and pover it goes into pairing mode and the blue light flashes but no phone that I have tried and sees it in the devices, is there a solution for this problem?

Hey all, have just received a ST20H, considerable scratching on the presence dial (only) would this be inherent to the amp?

Thanks!

Wondering how to turn off whatever it is in the amp that is receiving an AM radio station.

TIA

Jack

I´ve never palyed with an Amp Stand. I´ve got a CODE 100c and I would like to know if anyone has the esperience and if it is true that it feels diferent.

I am restoring a couple JCM800 Bass series 1552 cabinets. I can't find a replacment S15-250 16 ohm speaker to pair up with the others. What is a good replacement set of new speakers for my SS 3480 400 watt Integrated Bass System head?

Hallo Leute ich bin neuer besitzer einem Astoria Dual, hat jemand das Schematic von dem Amp?

so hätte ich alles zusammen. Danke .

Lieber Gruss Sandro

My new JTM45 acts strange on the input side. The two top inputs are supposed to be normal sensitivity and the two bottom ones lower sensitivity. On mine the two top inputs are just lower level, less treble versions of the bottom two inputs. Just sounding dull and lower level. Also, jumping the 1&2 inputs does not work. When jumping, channel 1 takes over and channel 2 almost does not add anything (just a tad) even when the normal loudness level is set to max (and the high treble loudness level is still low). What can I do?  

Where do I find the serial number for Kilburn 2? The number below the barcode does not get accepted while registering it.

Hi everyone, 

I lost a Minor III headset some time ago. I bought a second-hand one but I can't get the two headsets to work together.
I've tried resetting the box (pressing 15 times until the purple light comes on) but the earphones seem to remain identified, and above all they continue to work separately. Do you have any idea how to solve my problem?

Thank you 🙏

I just haven't been able to choose 3 presets and save them on the 91009 pedal. Could you please help me out with step by step instructions to be able to do this. I just want to be able to pick 3 presets on the amp and have them saved on the 91009 pedal. Nothing I've tried works.

HELP PLEASE!

Hi All,

I'd like to know when was the TSL line retired, Yesterday I got a TSL100 made in Late October 2010 according to the Serial number.

M-2010-43-0003-1 this tells me year 2010, week 43 (last week of october), 0003 unit number, is this unit number for the TSL? My TSL seems to be one of the last ones made, I guess.

because it is funny is that My JVM410 Serial number is M-2010-33-0619-1 this tells me year 2010, week 33 (second last week of august), 0619 unit number which is higher, would this be only for the JVM?

Cheers,

Andrés

was wondering if the 2 way footswitch can control the inbuilt pedals in the amp instead of making a whole new preset but with the pedals turned on?

also if the 2 way cant can the bigger footswitch?

I think that this forum should be dedicated, if not to Marshall Code exclusively, then to Marshall products and not to anything else such as advertisements that have nothing to do with music or our concerns and hobbies.

Greetings

I use the CODE 100 H. My question would be the following: I have configured some settings within a preset to play a song, but when it comes to the guitar solo, how can I increase the volume for the solo? And how can I reduce the volume after the solo? Do I need an external booster pedal? Do I have to have two different presets for the same song in order to have a separate volume for the solo? I hope you understand my question. I don't know how to increase the volume when I'm playing a song with a preset within the bank, when the guitar solo comes in. Do I need to configure two different banks, two different presets, or can I do it within the same preset? I hope you can help me. Thank you very much.

I purchased a brand new DSL40CR in late January.  10 days past the 45 day return policy for Guitar Center, the amp completely stopped working.  Took it to my local, authorized warranty repair location and a resistor was replaced.  Amp worked fine for a few days, but the LED's (red/green) would only show red when switching channels and master volumes.  Took it back again, this time the entire circuit board was replaced.  Amp worked for 2 days, then NO LEDs, no audio again.  Looks like the board will need to be replaced again.  Is this a common occurance with this model?  Is there no "lemon law" type policies where the defective product is finally replaced?  This is my very first Marshall amp, and so far the experience has been HORRIBLE.  I have been without an amp longer than it's been home and and usable.  Anyone else having the same issue?  So far I am NOT loving the legendary Marshall amp.

I recently picked up a used AVT 150H amp.  Unfortunately, it did not come with a footswitch.  Which footswitch do I need to order to properly work with this amp?

Thanks in advance.

Jerry Singleton

Hi

Would I be able to run 2xJVM 215C amps in stereo in 5 cable method ? I'm a little confused about the 2 x master volumes, I imagine that if I use one for my master volume (Master 1) I would adjust that to the same level on both amps and if I use the second master volume for solo level (Master 2) I would need to adjust that as well on the second (slave amp) as well as the master amp (the one with the preamp I'm using).

To access the solo boost on both amps I would send a midi PC command to both amps which would enable the Master 2 on each amp which would then be at the same level?

Would that be right please ?

Thanks

Paul