I am running Windows 10 on a compatible laptop and get an error message when I try to run the Marshall update utility software. It occurs after a "verifying application requirements" window pops up. The error starts with "An unexpected error just occurred. Cannot create instance of main window"?
Any advice?
Steve
When I save a preset in the app the preset will multiply as in there will be more than 1 of that location and none can be used. Is there any way to fix this? I tried deleting and redownloading the app but it happened again. Thanks!
i registered my amp, but it doesn't show on my profile page, have i done something wrong !
Hi, I recently purchased a brand new Marshall jvm410c amp.
I have a knob that is defective. It is crushed on the golden rim. It was given to me from the factory this way.
Will you please send an oem direct replacement knob for me?
Juan Ramirez
I need to clean my master volume pod but these dont look like your avrege pods. So really I'm asking if it would be ok?
hi, i registered my code 25 amp, but cant find anywhere in my profile ..... ie: my marshall (cloud) as to all my registered amps ?
I have a '77 jmp 100,currently through a 4x12,am looking at downsizing due to portability issues,but am loathe to part with this awesome amp that has been with me since the late 80s,so am considering using with a 2x12,any advice,regarding resistance values,suitable cabs,would be appreciated.
when can you sevice my 100 watt lead head .it packed up on a gig saturday
HI just got a new (3 days old) JVM 205C and played it a couple of times then when I went to turn it on again it will not make a sound!
It starts and all the tubes light up but when you turn off the standby nothing happens and no sound at all comes out, not a click as if the standby swith is doing nothing.
I did read the manual about the FX loop button muting the amp without effects plugged in but I have tried everything I can think of so far, guitars, leads other power sockets but no go!
Anybody have any ideas???
Thanks
Mark
It seemed to have installed CODE Audio interface, because I can see it is my Devices & Printers (Windows 8.1) as a composite device with a 2013 Microsoft driver installed. But it does not show up in my DAW at all.
Where is the driver and than in particular the ASIO driver for this????
It is connected, because when I use the WSAPI (Windows Shared API) is can see the SPEAKERS from code and play audio through there (horrible quality though). But not the input. Without that, this device has not much value for me.
Thanks for your help,
James
I registered my amp on My Marshall but I don"t see where it's listed. After I registered the amp I don't see it listed as part of my profile. There should be a "registered amp" tab so that I can access the serial number if I need it. Thanks.
I have looked high and low for a cover for my AS50D. The only luck I had was one place said they had them on backorder and I never heard back fom them. Any suggestions how I can get one - soon?
I do not know what year my TSL combo amp is but it is an older model. Will the foot switch for new TSL 60 or 100 watt work with my JCM2000-60W TSL 602 combo and if so where can I purchase a circuit board for the foot switch, the channel switches are bad but the reverb and the effect switches seem to be working OK they are turning on the indicator light on the pedal, but will not turn off the reverb and effects. Please help me with this if the circuit board needs replaced
is there a downloadable manual in Spanish language available for the CODE 25?
Any diagrams or recommendations for setting up the effects loop on a dsl40c?
Hi everyone,
Do you know in wich year does the jcm800 4104 Vertical imput as been producted..?
Thank you
how do I find original replacement parts such as ohm pin for pin socket/input/output jacks/small logo for amp head?
My amp is a 30mgfx and when I turn it on I need to move the gain to make it sound good and the power of the volume is not the same as when I bought it, what should I do?
Hello.
I have a marshall JVM 410 combo, and connected a extension cab JVMC 212,16 omh,I get an amazingly god sound.
Can I connect two JVMC 212 cabinet without damage the amp in any way? If not,is it a another way to connect one more cab?
Maybe I can use two 8 ohm cab?
I maybe ask silly no, but hope it is possible? :-)
Thanks for reply.
Greetings from Norway.
Does anyone know a way to combat the huge jump in volume when switching from Clean to Crunch on the Classic Gain channel? I’d like the switch to be as simple as pushing the button without the need to alter volume settings.