On the MyMarshall site, on the Presets page, I reorganized the default 100 presets to an order that makes more sense to me. I clicked the "Sync Now" button in the Gateway app and was pleased to see the new order displayed on the CODE50. However, when I toggle between AMP mode and Gateway mode using the icon in the lower left corner of the Gateway app, the order of Presets on the CODE50 also toggles back and forth between the original default order and the new order. How do I make my new order the default order on the CODE50, such that the new order will not change unless I do a factory reset?

Am I correct that clicking on the red "Reset Gateway Presets" button in the Gateway app would cause me to lose the new order created on the web page?

An annoying problem of Code 50 concerns the sound of low frequencies which are extremely "muddy"
using a Stratocaster's bridge single coils: absolutely no attack & non-existent twang!.

I really like this amplifier and I am sure that with a firmware update this problem can certainly be solved

My current firmware version is 1.44.

Cheers

I have an issue on my 1 year old DSL40CR.  The Clean/crunch channel is going out.  it has a fuzzy weak signal for a while and will eventually go away.  However, when I switch to the OD channel BOOM it works fine.   When this problem happens, I am turning the amp off and waiting a few minutes and I turn it back on and the amp works fine on the clean/crunch channel.  Seem to do it after the amp warms up a bit.  I bought it at GC and they suggested I take it to an electronic repair place in Dallas.  Has anyone else had this problem?

thank you

kevin

hi support

why do not you solve this problem???

my hardware:

Iphone X, iOS 12.1.4

Ipad Pro, iOS 12.1.4

Marshall Code 25, Firmware 1.4.1, date of purchase 12.03.2019

Hi! 

A newbie question here. Just bought the as50d amp and I'm a bit lost with the effects controls on it. So here's the thing that's bothering me, does the switches for channel one and two also control reverb or is reverb always on if the control nob is turned on of course. It is always on my amp if the nob is turned, even when non of the channel switches aren't pressed. Should it be like that that or is it something wrong with the amp? So should the channel switches next to chorus also turn on or off the reverb or not? 

Not a question, just a general observation for discussion. 

I've heard a lot of people saying they can only use a CODE 25 for home use with the master volume set at 2 or 3 .

The amp sounds much better with the master volume at 8 and the guitar volume set very low (using a Les Paul).  

The amp sounds much fuller and more responsive.

Hi, what footswitch is used with theAS50D? It said in manual PEDL-10029 can not find one to buy?

Thanks

Regards

I'm noticing a significant volume difference between the presets I have programmed on the footswitch in A2 & A3, is there a way to adjust this so the volume remains the same when switching between A2 & A3 ? 

i'd like to buy the right headphone to use with my code50, do you know the exit impedence from the headphone output mini jack?

Hello, excuse my english. 

I just bought a new dsl40cr and i'm very happy but i am experiencing the known problems that this amplifier present when change the channel through the footswitch along with having the FXLoop ON.

In several forums like marshallforum.com there are quite a few people who have found the same fault, which leads to me think that is not a random failure in some amps but something more like a manufacturing defect. Some people have already contacte with the Marshall staff so i understand that Marshall is aware of the problem. The question is whether they are going to appeal to these units so that the authorized technical service of each country solves the problem (it seems that replacing a chip) or we Will have to be the users that we have to take charge of the management of this defect. (still under warranty)

Thank you very much and Best regards! 

when I connect the app on android with the bluetooth amp and I want to load effects edited by other people, the effects return
by default, and when I deactivate the bluetooth again the edited effects appear in the library of the gateway app. Can not be
used when connected? I do not understand what happens.

Hi have a Marshall code 50 what usb cable do I buy to fit to a iPad Pro ?

I was having difficulty syncing my gateway app to my Marshall.com to add downloaded presets to my library. On the forums Marshal suggested doing a factory reset by holding the amp button down while restarting the amp. 
I did that. Now when I try to Bluetooth connect the gateway app and the amp I get this an error that says "connection rejected. You may only control amps you are already connected to for audio output". 
I have restarted the amp and phone but I keep getting the same error message. 

please advise on both this current problem as well as how to sync my gateway so that the downloaded presets get added to my gateway library. 

Does Marshall sell a cover for the CODE50?

Has anyone found an aftermarket cover that fits the CODE50?

Hi,

I got my DSL 20 CR in May 2020 so 6 months ago and recently have noticed that the light underneath the power switch is flickering.

It is now significantly dimmer and a bit annoying not really what you would expect with the quality of a marshall.

Not sure if this is covered by the warranty or if I need to fix it myself.

Any Help greatly appreciated,

Thanks

Thomas

i have connect my phone whit the amp code 50

but in de gataway app i see the code 50 but when i press connect he sais not connected 

so i dont work what is the problem

Where can you get a new master vol pot for code 100?? Mine has loud crackling and uneven volume increase-- it jumps and seems to get quieter on higher levels.  Tried cleaning it several times. 

I am trying to import patches from my Marshall Code 100 amp to Code Editor using a cable and even after reinstalling Code Editor it comes up with an error message "Error While Decoding System : Error_Bad_Device_ID" whenever I try and import a patch from my amp from selected patch number. This is despite the midi light being green, indicating connection with the amp. This is after not having used Code Editor for ages like 6 or 7 months or so. I am sure I had it working at some stage like 7 months ago or so. Is there any other software you can use to transfer patches from my amp to my pc and save them as a backup? And even modify them like you can in code editor and Gateway?

Hi, i have just aquired a haze 15 head in great nick.

please anybody could you advise on what marshal power tubes are used as in maker ?

Also they use three ecc83 the first being a different code ( this is the one with the aluminium cover) is this the higher gain one? if so could i swap for a lower gain with no problems.

Also has anyone upgraded the speaker that is fitted ( marque) ? if so to what just interested

Thanks John