Hallo, Freunde von Blues & Rock,

ich bin hier neu auf My.Marshall.com. Ich suche für den soeben neu gekauften Amp MG50GFX nach Manual und Datenblatt mit technischen Daten und möglicherweise ein Diagramm der Schaltung, Dasselbe suche ich auch für den viefach-Fußschalter "Stompware for MG".

Ferner suche ich Rat bei einem Sound-Problem. Liegt meine eingeschaltete Superstrat etwa einen Meter vor dem eingeschalteten Amp, so höre ich ein störendes Brummen (50Hz). Witzig ist dabei aber: mit dem 5-Wege-Schalter der Gitarre kann ich das Brummen ein- und ausschalten. Besonders deutlich brummt es, wenn ein Single-Coil-PU auf solo geschaltet wird. Der Humbucker macht hingegen genau das, was man von ihm erwartet: Er unterdrückt das Brummen,

Was kann man dagegen tun? Entstörfilter in die Signal-Chain einbauen? Abschirmung der Gitarre gegen störende Induktion verbessern (Faraday'scher Käfig) ?

Herzlichen Dank im Voraus

FarrierPete

------------------------------------------------------------------------------------------------------

Hello, friends of Blues & Rock,

I'm new here on My.Marshall.com. I'm looking for a manual and datasheet with technical data and possibly a diagram of the circuit for the MG50GFX amp I've just bought. I'm also looking for the same for the "Stompware for MG" multi-function footswitch.

I am also looking for advice on a sound problem. If my switched-on Superstrat is about one meter in front of the switched-on amp, I hear an annoying hum (50Hz). The funny thing is that I can switch the hum on and off with the guitar's 5-way switch. The hum is particularly noticeable when a single-coil PU is switched to solo. The humbucker, on the other hand, does exactly what you would expect it to do: it suppresses the hum,

What can you do about it? Install interference suppression filters in the signal chain? Improve the guitar's shielding against interfering induction (Faraday cage)?

Many thanks in advance

FarrierPete

When I plug in footswitch nothing happens no light anything tried another cable nothing both cable work with guitar so I'm thinking not cable 

was wondering if the 2 way footswitch can control the inbuilt pedals in the amp instead of making a whole new preset but with the pedals turned on?

also if the 2 way cant can the bigger footswitch?

I purchased a very nice and great sounding used but newer DSL40CR that came with the compatible 91016 six-button footswitch, but unfortunately it does not work. 

The standard footswitch that also came with the amp works fine. And I also checked 3 separate working cables, so it seems to be the footswitch itself. When you plug it in, it sort of uncontrollably cycles through channels and all six blue lights illuminate on the switch, but then nothing. Totally dead. 

I really was pumped at being able to set up four pre-sets, clean through lead and a few in between. Now I'm stuck with just the two playing live. 

That footswitch seems to be unavailable anywhere. Is anything else that is available compatible?

thanks!

Andrew

Clean Channel 1, FX Loop and the 6 Button footpedal stopped working entirely. I cannot switch to clean channel with the button on the amp either. Same for the FX loop. It was working fine last saturday 2/3/24 and by Monday this happened.

Channel 2 OD both Green and Red work fine and sound fine. Both Master Volumes work and the EQ section works. 

It's literally stuck on channel 2 and the FX loop and footswitch do not work.

Morning

I am wanting to set my number three pedal on the footswitch of my Code 50 as my tap tempo across all presets. Is this possible, or do I need to do it per preset?

Also - if you can please run me through how to do this.

Alun

I recently picked up a used AVT 150H amp.  Unfortunately, it did not come with a footswitch.  Which footswitch do I need to order to properly work with this amp?

Thanks in advance.

Jerry Singleton

Hi,

I own a Marshall JVM205C and would like to connect my Headrush Core via EXT AMP OUT to the footswitch input of the JVM205C. The Headrush manual states that this can only be done with a “short-to-sleeve” footswitch input without damaging the hardware.

Please let me know if the JVM205C has a “short-to-sleeve” footswitch input.

Best wishes and thanks in advance,

Peter

OK so I have been messing around with the 4 way footswitch, settings, and other ways to boost the volume of lead playing vs rhythm playing while live. I have already tried tweaking my volume settings in the app, and boosting the OD effects level as high as it will go, and there still is not a discernible difference in volume when playing live or at practice. I am wondering if I can just add a volume pedal inline between the guitar and amp to rectify this. A previous post I had on here someone told me to advust the volume setting per patch, but the problem I run into is when I set the main amp volume, it saves all the way across the board, and I cannot save individual parameters- for example, if I set my FS control to no OD on switch 1 and the volume in the app to 3, then turn on the OD and set the level of OD to 9.9, it does nothing in the way of significant volume output. I find myself tweaking the master knob in rehearsal to get the volume up. 

So I am assuming a volume pedal is my only alternative. Unless I am missing something here. I don't see a way to boost volume for a solo unless I want to duplicate the bank and then boost the volume on the adjacent bank and flip between the two? Is that the only solution here?

I have a Marshall Code 50 with the 4 way footswitch. I have learned how to activate the various effects in switch mode, but I haven't found a solid volume adjustment workaround. For instance, if I am playing rhythm and need to go lead, I can activate a switch and go to distortion, but the level isn't adequate to drive the sound to the right volume for a lead guitar. I have tried adjusting the "level", but it won't go over the master level on the preamp volume-wise. Is there a "volume pedal" like solution for this? I am not sure if I can run a volume pedal in sequence with the footswitch, has anyone tried this?

I bought a dsl 40crc from guitar center around 8 months ago. bought the 6 way footswitch. footswitch decided to only work on standby if it does come on while on either high watt or low watts turned on if I switch it it goes dead but if I swith amp to stand by it starts working again.? any answers to why this may be happening?

Hi I have a JVm410H and I'm looking at buying a Gig Rig G3 programmable footswitch so I can store various pedal combos, and then switch with one push, both the pedal combo I want and also the Marshall channel I want at the same time.

Is this possible using a) the Marshall footswitch or b) using the MIDI In/Out on the head?

Any help most appreciated

Cheers

Hello all

I am using a Code 25 together with a PEDL-91009 footswitch.

I would like to know if is it possible modify the volume using this pedal. I have read this thread:

(?

but it is not running, I am not getting different volume when changing the preset.

Your help is much appreciated ;-)

Kind regards,

Antonio R. 

My footswitch is not working, just random flashing of different led sticks and numbers - no change from the current preset I'm in.
Is there a way to activate a factory reset of the switch?

I have a DSL 100 And a DSL 100H , will the footswitch for the 100 work with the 100H or do I have an issue because mine is not working in the H ? 

Is there a user manual for a PEDL-91003 2-button footswitch?

Dear Marshall team:

I use the Code 25 amplifier, with the Gateway app and the Code series footswitch. The firmware is updated with the latest version available.

For a long time I have been noticing certain problems, mainly:

-The preset settings are changed on their own (sometimes the volume, other times the gain...) They are usually changed to the settings on the control knobs. I load the preset again, and after a while some of the settings are changed again.

-Another problem is that after using a preset for a while, when changing to another it does not change (it stays blocked). It does not respond either by using the pedal or by changing the preset from the app I have to turn off the amp. At first I thought it would be a Bluetooth problem, since I was using the Gateway application, with an iPhone. But now I'm using it with an Android phone and I continue to have the same problems.

Waiting for your comments, receive a cordial greeting.

Eduardo,

I got a M TSL 100W top with a bunch of Boss-pedals in a floor stomp board, including a stereo chorus and stereo delay (and the 5-way footswitch next to them). It would be nice if I could use the stereopedals in their fully potential, not in mono as I do today.

I got the money to buy another TSL and create a stereoset up, but will it work as I hope?

My thoughts/questions:

1. Do I need to have two (2) 5-way foot-switches  (one each for each amp)  to control both amps channels (I have looked at Voodoo labs-products but Iḿ notsure they would simplify this problem) 

2. Today I have the stomp-pedals in a loop. Would this be possible also in the stereo situation?

Thanks in advance for any answer.

Hi - just recieved a code 50 footswicth, new and out of the box..   Plugged in and no lights, used a ferw different cables but still no sign of life..  Any advice..?

Is the footswitch for the code discontinued?  I try to order it via Thomann but is not even in the list of the available products. 

Thanks