I was wondering if the creator of the KASHMIR preset would be interested in also creating the FLANGER part for KASHMIR using all the current preset settings (amp, cabinet, speaker etc) as a complimentary preset for the turnaround section of the song.  I believe, from forums, that a preset will switch better (Marshall CODE footswitch) if the preset has the same amp, speaker and or cabinet setting as it takes away the millisecond delay of switching between amps in a particular preset.  Look forward to your answer and or creation of said beasty.

Regards Kev

Hi there,

Just last week I purchased a brand new Marshall DSL40cr, and after playing through it for some minutes I noticed a "wind blowing on a microphone" sort of noise coming from it. I did some research online and found out that quite a few people have had the same problem with this amp. I'm guessing you must be aware of this by now and must also have the solution to this problem.

I live in Brazil, so I'd rather not have to send my amp back to where I bought it in the US, but instead take it to a local tech here in Brazil. I just need to know how to solve this problem. I've already talked to two technicians here, but they don't seem to know what to do about it. What have you found out about this "wind blowing sound" problem? How can I fix it?

Best wishes,

Frank

Hey guys

I bought a Marshall Code 100H about a month ago. (The cabinet also)

Now what i ask myselfe is. I have a strange cracking sound when I play with the Bridge Pickup. This only happens when I play a distortioned sound. All the clean sounds are perfect. Bus as soon I activate a distortion pedal, or put the gain up, there is this strange cracking. It's like an oversteering of distortion.

I tried with different cables, resetting the amp, with headphones, other guitars and another loudspeaker, but it's always the same.

Since I live in switzerland and I had to buy the amp in germany, it's kind of difficult to go to the dealer, because he's four hours driving away from my home.

Or do I have too high expectations on this amp, and this is totaly normal?

I recorded a sample of it, but I don't know where to upload.

Many thanks for your help.

Rock On!!!

hi all,

I ve got a helix hx I am trying to use for channel swap on the amp.

For all of the above the following applies:

- JVM footcontroller is disconnection

- JVM midi has been reset: its on MIDI channel 1

Boss ES5 (works)

I can get it working using a Boss ES5: https://www.youtube.com/watch?v=3YI65cgA4XI

Midi cable setup: Boss ES5 (out)  > JVM (IN)

 Also going from Boss through the helix (midi passthrough works).

Midi cable connection:  Boss ES 5 (out) > Helix (IN) > Helix (out) > JVM

However, this is using Midi patch panel change. Not sure how this differs from MIDI CC?

Helix HX (not working)

For Helix im following this video : https://youtu.be/simaPS7dzLw?t=55

Midi cable connection:   Helix (out) > JVM

Im using MIDI CC and following the table in JSH User manual.

channel : 1

Function: CC: 16

value 2

= clean channel, Orange mode.

I set the amp up so that the midi controller is BLINKING and it doesnt stop blinking: its not receiving the signal?

I feel like Im close to getting there.

Any ideas?

Thanks,

Eric

My serial number doesn’t seem right it reads 0 068 it seems to be missing a number is there only one location for the serial number?

Hi,

Does the Code 15, 50, 100 have the same proccessing power ?

is there any difference in the hardware/software version ?

Thanks

D.

Ok My phone won't let me download the Gateway App. Is there any other way to get into my presets and what not to turn on my Noisegate/threshold?

Hi my marshall 50 watt all solid state keeps cutting out...  i am not sure if its the footswitch i bought it online a few years ago.. its a 2 x 12 combo. 

it will play fine for like 10 minutes then the volume just dies down to almost not audible.  I am not doing anything to make that happen. i didn't even operate the footswitch. 

please advise,

 thanks, Nick

can anyone share or suggest a preset for Bowie's let's dance nile rodgers rhythm guitar?

I want to know if the midi foot controller Berhringer FCB 1010 is compatible in Marshall Code.
thanks

Does Marshall sell a cover for the CODE50?

Has anyone found an aftermarket cover that fits the CODE50?

It won't power up when switched on; no signs of life at all. It worked fine at a gig and then when I got it home, it wouldn't switch on.I s there a fuse inside the cabinet? I've replaced the fuse in the plug, but that hasn't helped. 

Just bough an MG30DFX. Warranty card states you can register online.......where?

Its not very apparant

Cheers

Windy

I sent my footswitch into our local repair shop a few years ago and they wired a new cord on. It has since had the 1/4” jack ripped off by accident.  I bought a replacement jack, but don’t know what part each of the four wires connects to in the jack. Thanks in advance!

Hi Guys there are many topics thrown the internet regarding which amp covers fits in each Marshall. Even the sales person from Guitar Center doesnt know precisaly which cover will fits perfectly in my Marshall's (I ahve plenty of them) so I decided to create a topic to check this, please help me with this models:
JVM410H
DSL5 (2014)

Valvestate VS100H

thanks in advance

The others amps I already have the cover

My Code 50 shuts off after a couple minutes.  I can turn it back on a couple times, then it wont turn back on.  If I let it sit an hour or so, then it will repeat this behaviour.

Hi!!

i just got a TSL 60 head , i been having problems with hum and noise and after a lot of research with my tech  we found out that they present many problems , wrong  values on components, defective  materials , ect . so he told me the best way its to change the board with the latest issue version!!

but the thing its that we counld find any info about how many version are  outside  and wich one is the latest ?

i was wondering if you can give the part number for the latest  version of the main board so can order it!!!

i would really appreciate that !!!

thanks 

Where and how do I register my new marshall amp? I am in the united states and your link for registration says its for people in the UK and Ireland and does not say how to register in the U.S.