Does anyone have a good heavy Robin Trower (like Bridge of sighs stuff early early stuff) and please don't say HENDRIX......thanks D.Wells
Hi all
Im trying to get close to Long Train Running Sound. Any tips please
Thanks in advance
When will ASIO-enabled firmware be released?
Having problems storing presets to foot switch- manual not helpful. Does anyone have step by step instructions? Many thanks
Hola, hace unos dias mi CODE 25 dejo de sonar. Lo prendo, las luces se encieinde, se conecta a Gate, suena por escasos segundo y luego deja de sonar. Lo apago, prendo y lo mismo asi sucesivamente. Alguna idea?
Or is the numbering of the presets ... haphazard?
Hi There,
For lowish volume practice I can currently run the SC20H on 20W mode with the master at about a 1, or just slightly above that on 5W mode (maybe just under 2) with the preamp at around 8 in both cases. Is there any benefit to getting an attenuator to be able to run the master at higher volumes?
While I am asking: Does the poweramp distortion of the amp behave differently in the 5W mode vs the 20W mode? I.e., in 5W mode does the power amp distort at lower numbers on the master volume than in 20W mode? For both modes, what is a good number at which above power amp section distortion is occuring (not factoring in specifics like pickups, etc)?
Thanks!
Hi, has anyone tried to control two DSL40CR or DSL100HR using one PEDL-91016?
Hi
Currently running my Code100H through the matched 4x12 cab but find, at volume, the sound a bit 'harsh'? i've actually plugged it through a spare bass cab and get far better tone! is anyone else experiencing this and are there any solutions? am i missing a trick?? i'm possibly looking at plugging it through a 1936v 2x12 cab. I know i will need to turn the cab selection off on the amp but just want a better all round tone..
tia
Hi, I need the Manufacture exact dimensions for a Silver Jubilee 2x12 Combo 2558.
Thank you
I know how to slave the two stacks together using the effect send of the primary and into the return of the slave head. How do I properly access and use my effects loop in this situation?
I have a Marshall Origin 50c. I was wondering where the sweetspot is for this amp. I have my gain on 6, my bass on 2 my mids on 3 and my treble on 4, tilt is on 6 , presence is on 7 and master is on 2. I use it mostly for clean tone, then use my distortion pedal for the distortion that I need. I am a at home guitar hobbiest, and would like to know where the sweetspot is for this amp.
Hi there,
after some time (months or weeks, I don't no) my Stanmore speaker plays from iPhone X very quietly. My iPhone is on maximum volume and Stanmore too. But my friends' devices play well. My iPhone plays well on other devices. Where is the problem? I can't find the solution.
Vlado
I would like to use my fractal Fx8 as a channel switcher but first I must know if the amp uses "short to sleeve" switching. Could someone give me a definitive answer to what kind of channel switching the Mg50fx uses? I wouldn't want to risk the potential damage to either pieces of gear. Thanks in advance.
In case Marshall decides to do another round of Codes, or for people that want to buy one, here is my bottom line after dealing with this thing for a few years. I had Line 6 experience and wanted a simpler all-in-one modeling combo with a bluetooth app that could do hard rock. The Katana looked like a toy so I bought this.
PROS: Solid construction. Looks great. Good range of amps and effects. Bluetooth app is very good and can tune every parameter. Tones can be downloaded and backed up to/from Marshall site. Amp can sound very good (after a lot of tweaking). The Plexi, American OD, JTM Crunch and Acoustic amps are good. The Guv’nor, Compressor, Chorus, noise gate and all the delays and reverbs are useable. Marshall has done sufficient software updates to correct early issues (bluetooth, tones, bugs). Can be used at bedroom volume with Master on ‘1’. Optional footswitch gives good control. Documentation is good. Updater software on PC works well.
CONS: Other than those mentioned above, all the other amps and effects are bad. This includes the JCM800, JVM and Silver Jubilee. All the cabs are bad. None of the stock patches are usable. You have to make your own. There are user uploaded patches you can try but very few are usable. Learning curve is significant. The amp is too loud. When you turn up from bedroom level to louder, the sounds change and become very boomy which should not happen with a modeling amp. No effects loop. The ‘out’ is a mini USB. Connecting to a computer requires a mini USB to USB or Lightning cable, which is not included. I tried to use the USB to record to Garageband and sound came out but I couldn’t make it sound good. The footswitch also has a learning curve, and like other people I had to have mine replaced.
ADVICE: Don’t buy it. I bought my Code 50 new from Sweetwater for $299 and now the same version of the amp is $399. If you must have a Code, get the 25 instead. It is cheaper and still absurdly loud. The higher volume available in the 50 is useless because it sounds bad. The extra hundred bucks just gets you painfully loud solid state power amp watts.
If you do get a Code, upgrade all the firmware immediately. You need to connect to a computer to do this, but first you have to find the cable on Amazon. This is unforgivable.
BOTTOM LINE: I have spent too many hours tweaking the Code. This is what I hated about Line 6. But the Line 6 tones were superior. I never got a good JCM 800 sound out of the Code, after hundreds of hours of work. It’s only “great” amp sim, oddly, is the American OD. Marshall’s own Classic Metal patch uses this, not a “Marshall” sim! The Code is marketed as Marshall technology with amp sims created by Marshall, but it is not. Softube created the software and tones. This is not a Marshall amp. Line 6 Marshall sims are far better.
I have now bought a tube amp. I am keeping the Code because I have mastered it and can practice on it but I would not buy it again, certainly not for $399.
Hello All,
I have recently received the Marshall Acton 2 speaker which has a very good sound and design.
However it works only on my IOS phone, under Windows 10, I can pair the device but get's a message of battery low and cannot choose it as speaker.
Can you help me? 10.0.0.0.1 192.168.10.1 192.168.10.1
Whenever I run the update everything works fine until it completes at which point the amp goes back to saying "Ready for Update" and the website says the update was not completed and to restart my computer and try again.
I recently got a new iPadPro. I can Bluetooth to my Code25, but when I open the MyMarshall app I get the following: "Context 3D not available! Possible reasons: wrong renderMode or missing device support." What does that mean and how do I get the app to open? I deleted the app and reinstalled and have powered the 25 down and restarted.
Hello everyone, I would like to ask you specifically about the Marshall 1960B Lead Cab:
It says that it is made in England but I would like to know if the speakers that it has from the factory are the Chinese CELESTION's G12T-75 or are they made in the UK CELESTION´S?
Does anyone have this booth that can answer this question for me?
I thank you all
i have a marshal code 25, and i have always wondered, what does the exit/store button next to the digital pannel do?