I'm expecting my Mini Silver Jubilee head to arrive tomorrow. I have two 1x12 cabs I want to use at the same time. One is a 8ohm Mesa Boogie. The other is a 16 ohm Orange cab. My question is; is it possible to use both cabs at the same time? I'm looking at the manual and I'm not so sure. Plug the Orange into the 16 ohm output and The Boogie into a 8 ohm output? Or would that be too much of a load? Thanks.
Would you be able to check if my amp registration went through correctly? Code 50. Wouldn't want to miss out on the extended warranty.
Hi, I'd ke to use an external speaker with my Code 25.
Is it possible to use a 8 Ohm external speaker without any trouble ?
Thanks for your answer.
Hi, I've just bought a DSL5C combo that sounds fabulous.
Just to know when I will have to make tubes replacement, can you tell me:
I just wanted to ask why the amp head is in standby mode when the switch is in the off position, rather than the on? Rather confusing, and seems others have run into this as well but with no real answer. Or is something wired wrong on some heads? Full playing power comes up with the standby switch set to on, which seems backwards, so I'm asking what the reason is for this. Thanks!
just got the amp home
spent an hour trying to connect to an iphone 6s...it will not connect
what is the fault...it appears I am not the only one struggling to connect an iphone
where do i find the detailes ownwers manual on your site please
Hi I thinking about purchasing a footswitch for a MG100 Marshall head I have a G100R Head will these work together?
I've 2 old marshall 1912 speaker cabinets and 2 questions:
1) how can I remove the front panel for cleaning the grid?
2) there's a dedicated cover for the 1912 cabinets?
Thanks a lot
Hi Folks, it seems like a good number of the presets have this wierd thing where the low E sounds really dead and overwhelming, like one giant "PLUNK". I need to turn B down to almost 0 in some cases. This is mostly for single coils which is strange since all other strings seem to be brighter as youwould expect with SCs, just the low E has this strange sonic sig. Same guitars sound fine on my Quilter, DR, even my little Vox mini. I can "tone" it out for the most part. Is anyone else experiencing the same symptoms?
I'm from Spain. Marshall has official repair service in Spain? Can I Ship from Spain my Marshall to the factory to service or repair it?
My JCM 900 doesn't sound the same as it use to, had a local tech. put in a new transformer and tubes but, no balls. How do you find a trained Marshall service rep. in the states?
I bought a 75 Reverb 5275 amp, but couldn't find this amp in the list.
Is there another code for registration for this type amp?
I have an iPad 2 with 64 GigB and G3, using iOS v.7.1.
Downloaded Gateway. Pairing not possible most of the time, even when I put the iPad right on top of the Code 25 amp.
When paired, the Gateway software does not recognize the pairing and does not show a Bluetooth device indication on the bottom left corner. Go to set up, menu shows no Bluetooth connection even after the pairing was successful. Hit the Scan button but, nothing happens.
Please help. Thanks!
I bought a MG15HCFX amp. from Sam Ash in Sarasota Florida - I am unable to find anything about it on line or on your site - would like info on all of it's features so I can get the best sounds from it - please help - Thank you - Reeshark@comcast.net
Good afternoon! I've bought this amp one mounth ago, and I can't find any general informations about it on the web on the website of Marhall amplification. Has anyone found anyhting? Could you send me a link? Thank you!
I am running Windows 10. When I plug in the USB cable and run the updater - it says Code found, but has a spinnin circle that says "Waiting for USB". Any ideas?
I have a 2000 JCM 2000 DSL. I've read much about bias drift being a problem on some of the early ones due to a defective PCB main board. Are the replacement boards available commercially free of this defect? Is there a specific issue of board to get in order to be free of the problem? I don't have the issue presently on my amp but am considering buying a board to have as a backup.
I own a mg100 hcfx which I am very happy with. Although it didn't come easy. It was anemic sounding out of the box but with a boost and eq in front sounds like it should.(Also a noise gate run in x pattern in front and loop quieted the noisy mg) Question: where about do other users of this amp or similar channel switchers prefer their channel volumes? I know it's function is to equalize volume between channels but is it best to equalize them towards full volumes? Half volumes? Thanks!
I would like to register my head Astoria Custom, but I do not know what to enter in the "Amp Model (Product Code)" because AST2H generates the message "Unable to find any products That match"