1) Is there a way to sharpen the pick attack tone when the amp is on Ultra Gain 2? It has a dull, muffled attack. I've increased the treble and presence but this is no true remedy. I keep the drive setting at 12:00-1:00 on UG2.
2) Is there a way to reduce the deep compression when the gain is increased on UD2? It's a shame I can't have more drive and sustain in this condition.
I love the tone of the amp but I'd like to clean it up.
Are the power (mains) transformer in the Studio JTM head and the Studio Vintage head the identical model transformer?
my code 50 cuts out while playing. this started happing last year when i got it. I did all the software updates and i can only play 5 minutes. I went on line research and dont see anything for this problem, do you think the amp is a defect, im not sure what to do next.
Hello everyone,
I was wondering....
How can I get the date of manufacture for an AVT 150 from the serial # on the amp?
Is there a separate serial # on the speaker attached to the amp (and another date of manufacture?)
Are there any free websites to look up either or both numbers?
If there are, can you please post a link or links?
Thank you.
I'm a bit frustrated. I love my Monitor II A.N.C headphones, but they suddenly broke over night. After recharching, the phones signaled low battery after short time of usage. Now the battery is loading for quite a while without getting the LED to white. As soon as I disconnect the headphones from the power cable, it doesn't respond at all. It's not possible to switch it on pushing the control knob. When plugged in, it sometimes starts but goes off immediately again.
I can only use it via audio cable connection but not via Bluetooth anymore.
The thing is, this is the second time I experienced such a malfunction. I bought my first Monitor II six years ago and it broke after three.
Now the second pair broke after three years as well. Is this really a ooincidence?
I tried a hardware reset of the headphones but that did not work either.
Has anyone of you experienced such a behavior as well?
I have sent this amp to you twice and the last time you said that the amplifier section was renewed.
Most of the problems were solved by this, however, it plays nicely in clean mode but when I press the switch to crunch then back it goes off.
Leaving the amp switched off for a fairly long period and then switching on, it comes back.
Is there anything that I could do to alleviate this as I don`t want to send it back for this if I don`t have to.
Bonsoir la team!
Je suis à la recherche d'une radio cd
qui pourrait envoyer le son sur ma Marshall Stanmore II .
Avez-vous une marque compatible svp🙏 ?
J'ai fait des recherches, mais je ne trouve rien 😔...
Merci pour vos réponses 😁!
Bonne soirée !
I just bought a Marshall DSL 100 and trying find acabinet suitable for the amp. Thanks.
Is there a Led Zeppelin preset for the Code 50 amp? If so, what is the number, or the settings? Thanks
My Marshall Code 100h's blutooth daughterboard has broken causing the amp to be unusable. Marshal advised after looking at it that they do not stock any replacements. Does anyone know where I might find a replacement board as the amp is now discontinued and cannot source a second-hand one anywhere?
Getting issue in andriod phone in while pairing via marshall blutooth app. But in ios it is working fine.
What foot switch required: JCM 2000 (DSL 100)?
Where do I find the serial number for Kilburn 2? The number below the barcode does not get accepted while registering it.
Hello,
I purchased the Kilburn 2 from the official website a month ago. I usually keep it charged, so I didn't notice, but this time I used it until the battery was completely drained. After that, no matter how long I charge it, it won't turn on again. It seems like the battery is completely discharged. Is it normal for such a battery issue to occur after just one month? In this case, where should I request a repair?
Additionally, am I eligible for a warranty?
I've already contacted the official website, but I haven't received a response yet, and it's really frustrating 😢. I enjoyed using the speaker for a month, but now living without it feels so lifeless...
Thank you
The main problem of Marshall Code is a bad cabinet simulation. You may just turn off this button right on your amp and the sound will get better. Moreover, the compressor helped me as well. If you want to use distortion/overdrive, you may switch Pre FX from this pedal to compressor, but change your amp by means of the button on your amp to sone amp with OD letters in its name. And of course set Gain to it Max setting. You will get such a great but distorted/overdriven (depends on Gain) sound.
does anyone know if the first 4 characters of the cab serial number is the year of construction? and for my 1922 2x12 (potentially 2006) is this before of after manufacture changed from mdf to ply?
thanks Simon
I am not very good at sitting down and trying to dial in tones, so I rely a lot on presets developed by others. I am a huge phan of Trey Anastasio, and I am interested to know if anyone has found a way to come close to finding a preset line up replicating his tone. His sustain is always unreal, as is his control of dynamics. I am also trying to figure out what other gear I might be able to pair with my CODE 50 to try and replicate some of his tones, like adding a volume pedal, a wah, and a tube screamer.
So I have a brand new DSL100HR-U head and MX412a cab. when on the clean channel the proverbial wind noise comes threw. all mu other amp cab setups are working fine with the MX412a and it is not the cab. Everything from power conditioner to the cables are new as well. the only thing i havent done is swwitching out valves. Any thoughts or advice? Also to mention I'm a blind musician. and firstish timer amp troubleshooter
gdzie znajdę aplikację CODE EDITOR MARSCHALL? CHCĘ SCIĄGNĄĆ NA KOMPA
