I just picked up a valvestate vs100 with a different kind of grill cloth and red lettering..can anyone tell more about it and maybe the year it was manufactured...thanks Jeff....
Hi,
I have a DSL40CR - great amp- but sometimes the reverb is gone all of a sudden. When I swith off the amp and turn it on, the reverb is again audible. I use the 6-way footcontroller for switching channels. Any ideas? The amp hasn´t any others issues.
I'm getting the impression, the tech I'm dealing with thinks I or my settings could be the cause, due to the fact I guess this is the second time within a year I've had this problem. I don't push the amp hard. It's in a 10 x10 room I converted to a studio for recording. Maybe you would be so kind as to help me again. My current settings for volume are:
Overdrive channel Gain is @ 2 Volume is at 75%. On the clean/crunch channel the gain is at 8 and the volume at 75%. The masters are both at about 2. This gives me a good tone at a low volume. In the small room, it's in turning the masters up even to just 5 would require ear protection.
The question is are theses settings pushing the power or preamp tubes to the point that would shorten their lifespan?
Hi,
Got my amp a week ago, set it on a sturdy table, plugged it in, and it cranked. Played all week, having a great old time, but last night I plug in, and it's just not very loud? What did I do? I haven't touched anything but the power switch. Room's warm, I let the it warm up [got a little too warm maybe]. Anyway I'm on clear channel and have all the knobs maxed, and it just sounds, average, low, like a background sound. So strange. I'm not too crazy about tearing into an amp I just got a week ago, nor am I hyped to haul this thing to a Post Office either. Please tell me there's a magic button or that I did something stupid.
I have an Origin 20 Combo and I just bought a new set of tubes, and I was wondering if i have to take it to a technician to bias it, or even if it needs to be biased?
THANKS
I had a problem less than a year ago. I heard a light popping sound, then another then no sound. The amp was repaired under warranty. I was setting up to record. I turned the amp on, tuned up while I wanted for the tubes to warm up and when I brought the amp out of standby I heard that familiar pop. Kind of like a lightbulb popping. I have had tube amps in the past and never had to replace tubes so regularly. Is this an issue with this model Marshall?
Hi. Just verifying. Can I use The Behringer HA400 power headphone amplifier through the DI with the origin head without the cab attached or only into a mixing desk before removing the speaker ?
I’m just looking for best way to use headphones without the speaker attached .
thanks.
P.s the origin amp is awesome. Love it.
I was wondering what Marshall foot switch I could use and if it is still available? If not, do you know of any aftermarker ones on the market?
Thanks
Hi, Do someone know if the "custom voiced" speakers on a CODE 4x12 8ohm cabinet are the same as in the mg412a cabinet ? The mg cab is loaded with celestion g12-412mg 8ohm speakers that look like celestion rocket 50 but seem to be rated at 30 watts ... because the cab is rated 120w... some AVT cabs are loaded with celestion g12-412avt and some with celestion rocket 50 but AVT cabs are 16ohm (maybe the cause of suffixes change on the g12..) I've browsed the celestion website to find some answer and the only one that had the same magnet is the rocket 50 and is rated to 50 watts... i would like to know what kind of speakers are on the CODE cab and if the mg412a cabinet sounds about the same as the CODE 412 cab with a CODE 100h head ...i don't like the format of the CODE cab...but want to keep all the tone modeling capabilities of the CODE 100w head
My Amp came with a registration card and at the top "Register online at www.marshallusa.com/warranty". This page does not exist nor does www.marshallusa.com. What is the proper method for registering? This sort of lessens the Marshall Experience, Dont you think?
Is it recommended that the outside (tolex?) of this combo amp be cleaned periodically? If so, using what? Leather cleaner/conditioner? Armour All? Pledge? Something else?
I have tried everything to do the firmware update on my new Code 25. Its showing v1.11 still.
I have tried Crome, Edge, and downloading the manual windows exe. I have updated drivers, booted amp in "safe mode" (which identified usb as READY but still wonnect connect in My.Marshall
Please help! I love the amp but need to be able to update the firmware
Hi all! I'm building a new pedalboard and was considering getting this footswitch... Anybody who has one, want to measure it for me? Thanks!
Hi, guyz!
I wanna buy some good headphones for using with my Code, but I don't know the best suitable impedance. Didn't find some tech information in specs T_T.
I think, Beyerdynamic DT 770 will be a great choice, but 80 or 250 Ohm?
Hi.
At the beginning I want to point out that I am a beginner.
I have marshall code 25 and would like to connect a g3n zoom to it. Can anyone help me and describe what should be all settings on the amplifier to be clean. And the effect was from zoom. Should all knobs be screwed on? . As if someone were nice and described to me every setting I would change to, I would be grateful.
My new Code 50 is bad noisy out of the box. I have tried 3 cables, 2 diffrent Guitars. I have tried a diffrent Outlet. Nothing seems to stop the noise.
I can turn the preset to some that are quiter, but almost all have a noticiable amount of noise and or Buzzing sound.
I have tried Firmware upgrade, IT was the same version, so I reinstalled not luck.
Please help.
I was searching for lessons that I watched at Marshall Amps site in the 2000's. I know it's awhile ago, but does anyone know if Online Lessons are available still?
Hi there..
purchased a code 100 head and 212 cab from a guy on ebay.. sadly there is a lot of feed coming from the loud speaker output, reading into this, it's been a bit of a problem for you..
Any idea when you lot are back from lockdown, so I can pop in to have it looked at...
Many thanks..
Simon
Can i use code 100H only with headphones , without the speaker connected?
many thanks in advance
Giampiero