Hi. By mistake, I think I hooked up my 100 watt JCM 800 head to my 1960B 4x12 cab on mono with two cables. It's only recently that I figured out the right way to connect them. That's by plugging  one end to the 16 ohm output of my amp head since it's set to 16 ohms and the other end of the cable to the 16 ohms input on the right side of my cab. Will my stupidity affect the functioning of my amp head for the worst? It seems to sound and function fine now though. Thank you in advance.

I was very disappointed by the lack of the ability to disable direct monitoring of the CODE signal by VST ... I'm not satisfied with the sound quality of the CAB-sim, but I really like the sound of the AMP and I wanted to use CODE through VST with IRs - but in parallel with the VST there is always direct monitoring from the Code and does my work in vain...(( 

USB

Line IN

the chorus on my Code 50 is not working. I’ve had the amp about half a year, but not really used the chorus until recently. 

If I turn the chorus on, the sound changes a little bit, but it’s not a chorus sound – although the speed option has an effect. 

If I switch between CLS and VIB a few times, sometimes the chorus will suddenly kick in, and sound good, but if I turn it off or change presets, the chorus reverts back to its barely-there sound. 

Has as anyone else suffered from this? Any tips? Thanks. 

I recently added the tuner to my footswitch (preset), but now I want to undo it. I'd rather have the first bank available for a pre fx- preset. Doe anybody know how to undo it, ig by resetting the footswitch to factory settings?

thanks

Which do you think is the best amp attenuator for my Les Paul Traditional+JCM 800 2203+4x12 cabinet. Plz recommend.

I noticed while using the FX loop on the marshal dsl head the volume is somewhat lower than when I dont use the FX loop.

Is this normal?.

senhores meu marchall valvestate2000 parou de trabalhar.

a causa disso foi o CI de potencia, e alguem trocou por um equivalente(penso) qual seria o original.

bei meinem smartphone ist die Buchse für Kopfhörer 2 defekt.

Was kann ich tun?

Hi, I have successfully been able to pair my Iphone 5s to the Code 25 2 times now, and when I try to connect my gateway app to the amp, it never finds it. I've tried till I'm blue in the face, and they just will not connect to each other......frustrated!  TY

Does anyone else have a problem with the Code Editor software not fully displaying on the screen? Only the left half of the screen shows.

Does anyone have any tips for using the headphone jack on a Code 50 as a line-out to a mixer that goes into a PA system? I tried it over the weekendand it sounded terrible.

Hey

Hoping for someone to clarify my confusion

I have a 100 Watt JCM 800 head - Model 2203 - Serial No S/A T11842

I checked the Serial No online & the website says its 1985 - No problem there

However, the website states that a 2203 models Serial Number should start either SL or SL/A & that numbers starting S/A are 50 watts ?

I'm sure its 100w, but just after confirmation please

Cheers

Hello all,

I have had my Marshall CODE 50 since last summer with no issues whatsoever...until now.  Today when I decided to turn on my amp it was going NUTS.  Whenever I turned up the Master dial my presets kept changing rapidly on their own and the amp would not output sound whatsoever.  I tried updating the system's firmware and even performed a factory reset but nothing helped.  Has anyone experienced a similar problem?  Any advice or help in the right direction would be greatly appreciated.

hey Team Marshall,

I have the foot controller and a Code 50. Dig them both, GREAT AMP!! How do I over write a stored preset on the controller. Ex: on A1 I have DSL CLEAN I want to assign the TUNER to A1 then on A2 assign DSL CLEAN. 

I just recieved my Code 50, and am still trying to learn how to use it. The main thing I'm interested in doing and learning is using an expression pedal to go between sets but am not sure how to go about it. I was told I may need to get the additional Code footswitch to make that possible. Help please! 

Hell to all,

I recently bought a Marshall DSL 100 hr head and after a few weeks there is no sound if I choose the 100W setting, it will work on the 50 w setting. A few days back I noticed that if I used the FX loop the volume drops. I asked my dealer Guitar center in San Diego CA US, and they told me I need to contact Marshall US first for the warranty, even though the warrantly specifically says to return to dealer. Please help, the amp is not cheap and I have important gigs coming up.

Thank you.

Hi, is it correct that the light on the ampli related to the effects loop remains always on with the pedal-90012 connected?

Additionally Lights on the pedal do not switch on, is it correct?

 I have a CODE 25 that I’m gonna be using to record. The pitch shifter sounds artificial set to an octave down to simulate a bass. I also have a Digitech GNX4. Can a bass be run through the CODE25, or should I use the GNX4’s Whammy effect to do bass?

When I play music from my phone through the amp with an auxiliary chord, it just sounds muffled compared to my phone speakers or my headphone speakers. Is it the speaker or is there something that has to be done with gateway?