my code 25 is connect to the phone whit bluethoot, but nothing happens , the preset cannot be changed .......who can help me? 

Hallo an alle,

weiß jemand warum der Code 100 nicht mehr angeboten wird?

Grüße, Nico

I have a Marshall DSL40CR. I have checked the amps bias 5 days in a row and every day it's lower than what I have set it to. I was told bias in 40 watt mode should be around 35. When I set it to that on the first day and played...it sounded excellent. I put it in standby and powered off. The next day I turned it on with standby on and waited around 5-10 minutes. When I went to play it sounded really off. So I decided to check the bias and 1 tube was at 30 and the other 33. I reset both to 35. 

The next day after that I had to set it yet again because it was 30/31. The next day after that the same thing lol. 

Would this be an Amp issue or Tube issue? Once I set the tubes to 35...plays and sounds great the entire time I play. However, if I shut the amp off and come back later the amp bias is always lower.

Hi,

After connecting my device to the speaker, the speaker plays sound normally and the volume increases/decreases as my device volume increases/decreases. However, if I set my device volume all the way to zero, the speaker is still playing sound. Tried to reconnect, but still not working. Is there a way to fix this? I would expect the speaker to be silent when the device volume set to zero.

Thanks!

Salut tout l'monde!

Une petite question pour connaître vos expériences avec le modèle Kilburn II.

Quand l'appareil est relié via un câble stéréo en réception d'une table de mixage, la connexion Bluetooth devient instable et offre des micro-coupures de 2-3 secondes toute les cinq minutes environ, sans déconnexion de l'appareil.

L'effet se produit même quand la table est éteinte, et quelque soit l'émetteur radio.

D'autres utilisateurs ont déjà fait face à ce désagrément ?

After using Minor III  by use wear only one side per time for 2 or 3 days, my phone can't connect to the left side. I decided to unpair then pair again, I can only pair to the phone but can't connect to the in-air and  bluetooth system say "An app is needed to use this device". I also uninstall application then install again but can't fix this problem. How should I do?

Thank you,

View

I'm restoring a couple Marshall speaker cabinets, maybe from the 90's. Two of the above speakers are not working. 

Thanks,

Paul Haggett

alguien podria ayudarme con un preset que emule el sonido para el Solo de Audioslave Like Stone

I've got a beautiful JMP 2203 top from 1979, and I'm now waiting for my brand new 1960AHW cabinet to arrive. The problem is that the cab is 16 ohms, and it's only possible to select 4 or 8 ohms output on the switch on the back of my amp. The switch actually have 5 possible positions, but only 4 and 8 ohms are printed on the switch. It also has got a seperate label on the back that specifies 4 or 8 ohms.

I read somewhere that the Canadian amps didn't have 16 ohm output because of some Canadian rules, but my amp is originally sold in Scandinavia (Sweden), as one can see on the label on the back of the amp. Is there a "hidden" 16 ohm posibillity when I set the switch to the position after 8 ohm? Will I have to rewire my new cab to 4 ohms before I can use it? Any help will be much apreciated...

So, I have had this problem on my CODE 50.

I turn it on, plugged my guitar in it, everything normally, but after some seconds or minutes playing, it just get muted on! 

The funny thing is that the Bluetooth keeps working on... I tried to eliminate some bad connection but I never found one. My cable is good, my guitar is good too... I don't know, it maybe could be a board problem or a electrical/power supply fault... 

The Amp and display are up to the date, firmware 1.47.

Please any advice is welcomed 

Hi all,

I bought my Code 100 in Australia, where the voltage is 220 V and the amp only works with 50Hz as indicated on the back of it (unlike many other products that work with both 50/60 Hz).

Now that I have moved to the US, I am not able to use it anymore! I purchased a 110 v to 220 v step up transformer, which is fine, but cannot change the frequency from US's 60Hz to 50Hz to safely turn on the amp!

Frequency converters are like $1000 or so, so definitely don't worth it!

Is it possible to request Marshall's company itself to change the power board or something to make it work normally in the US without transformers, converters, etc.?

Would it be safe to just use the step up tarnsformer and ignore the frequency (Hz) difference?

Really appreciate any suggestions or guidance,

Thank you in advance!

Hi,

I just bought a Origin 50H head as a spare for my DSL 100hr while it is in the shop. The problem I'm having is I can only plug one speaker cab at a time, one is a 16 ohm cab with 4 12's, the other is a 8 ohm with 2 12 inch V30's. when they are both pluged in only the 8ohm 2 12's work, if I unplug the 2 12 cab then the 4 12's work. Is this normal or should I return it?

Thanks for your time.

What footswitch should I use when Pedl-10010 (P803) are discontinued.

Regards,

TC

Hello, I have a JVM410 100 watt combo with the 6-button footswitch.  I am seriously considering buying the marshall dsl20cr for smaller gigs, rehearsals and to have something lighter.  I know it comes with a 2-button footswitch.  My question is: will the 6 button footswitch work with the marshall dsl20cr?  I would like to be able to use the 6-button to have more control and switch between the gain stages of each channel, not just from one channel to another.   Thank you, 

i got my code 50 about a month ago now and it paired to bluetooth no problem for about 2 weeks and it was working flawlessly, but until about 2 weeks ago i went to connect to the amp and it does not pop up... i tried using my mums tablet, nothing, my dads phone, nothing aswell even my pc because it has bluetooth capability, nope... ive reset the amp and it got rid of all my saved presets and bluetooth still doesnt pop up on any device i use... can someone please help me?

Hi Everyone,

I bought a Marshall Studio Vintage Head in US where we have 110V voltage and 60Hz frequency. If I want to use that amp in Italy, where the voltage is 220V and 50Hz frequency, is it okay if I only change the currently mounted (US-rated) fuse? Or do I need to get a transformer? I am not sure if the amp is only rated for 110V / 60Hz...I like to think that it was built for a range of V and Hz that works for Italy / Europe as well, being made in UK.

If the fuse is the only mod I have to do, then I can just use a campatible power cord to plug it in?

Forgive my ignorance, and thanks in advance.

Antonello

How can I reinstall all the 100 factory presets (and overwrite all my selfmade presets) ???

Why is there no profile save button in ios and when there is a drop down it doesn't work, for example om the overdrive peddle you can't select GUV ODR or DIS it just pings back to what it was set on.

 I have a DSL20W ! marshall amp wondering how do I connect to my Bluetooth 

Why boost pedal doesn't work at Marshall code 50? I have plugged the electric guitar into volume pedal and the volume pedal into guitar input on amp, but haven't had no boost effect! Will volume pedal work? I'd like to boost my solos, anyone faced this problem?