Can I use the Code 100H as a pre-amp connected to a TSL 100?
My Marshall III button doesnt work so it doesnt display the blue LED light and i cant connect it to the app
I know very little about screw sizes and such. I have an Altec Lansing Speaker that I want to put into a DSL40CR. However, when I went to put in the screws I realized that the stock screws will not reach the nut on the underside of the baffle. Kind of at a loss. I'm asking if there's a longer screw I can get without changing the T-nut on the front of the baffle? So in other words longer screw, same t-nut. If so, anyone have an idea of size?
****nevermind I figured it out that they make longer size screws of the same screw and they were right at the hardware store!****
Over the past few days I have been switching between the modes and I noticed, that the low output mode makes a very funny noise, like it was underwater and that the high output mode was making crackling noises. Today, all three modes barely make any sound even if I turn the volume up to the max. What could be the problem?
Salut je recherche de très bon preset ou son Marshall , en effet j'ai acheté un Marshall code 50 cet année et j'en suis très heureux !
est ce que quelqu'un pourait m'aider, je suis plûtot pour le métal ou rock
merci !!
hello,
i own 2 DSL 40 amps, 16 ohms each, but one has three loudspeaker options: (8 ohm) - (8 ohm) - (16 ohm)
the other one has more options, (16 ohm) - (1 x 8 ohm) or (2 x 16 ohm) - (1 x 4 ohm) or (2 x 8 ohm)
I want to use one amp as an extension cabinet for the other one, and also as a spare amp,
how do i proceed with the connections ? the spare amp needs to be turned on ? will it work as an extension cabinet if not turned on ?
thank you
Bonjour
Quelqu'un aurait il la notice détaillée du DSL 5 CR s'il vous plaît?
Merci d'avance
Ive just bought a second hand jcm900 4102 combo. its from about 97/98. its my first valve amp, and when i brought it home i had a look round it, and noticed that two of the power tubes had cracked, so i changed all 4. all the preamp tubes are fine. but even though ive just changed them, there is no sound coming out of this amp at all, not even a crackle. HELP!!!
Guida all'uso dell'app Marshall Gateway
Instale el ultimo firmware y no me gusto. Se puede volver al anterior?
I bought my amp in 2017 I think it was the first series, it was totally new thing on the market. It went wrong about a mounth ago. I brought it to a dedicated engineer, who knew what could be the problem, He told that it is a common mistake with these amps (I don't know the exact english name of it) , where the elctricity arrives to the amp was too sensitive. Marshall changed it later. There is no part for the original, the new part is not good for the old amp, so there is no way to repair it. Is it true?
What can I do? The firmware update stopped at 97% and the Marshall Code no longer works! Unfortunately there is no correct help on the community! I've tried all of Marshall's suggestions, but Marshall Code still doesn't work! Marshall Code and Mac is not compatible. Can anyone really help? Marshall's software engineers definitely can't do it. I call that; big shit!
When trying to preform first time firmware update in browser it says "CODE: Not connected", although cable is connected.
Hi,
My Code 50 sounds cold, lifeless, scratchy at room volume. As soon as it is turned up, the sound comes to life. Is there a way to improve the sound when it is set to low?
Today my neighbor came over to jam and brought an electronic pedal arena 2000. I noticed the guitar volume was much higher than it should be as I had the volume on input 1 all the way down. We unplugged the pedal and found the amp volume would go up and then down as we played, we plugged a guitar into input 2 and found that both guitars would ramp up and then down.
the amp is 15 years old and doesn't get much play as it's a bit too much for the small room (realistically it may have 100 hours total at lower volumes), it has been parked in same spot all this time.
any help would be appreciated
Frank in Florida
Asked by xavi Fernández Gaya - 08 Mar 2024 at 09:08 AM.....
1. Does this problem occur for all presets? Yes
2. "My potentiometers are almost at "10" - what ptentiometers do you mean? I mean the The volume control buttons for the master volume and volume
3. Do you use any of PRE FX effects like compressor or distortion? If so - what are volume settings of these effects?Yes, I do use pre-fx like compressor or distortions, but they come in programmed presets. How does the volume of these pre-fx settings influence it?
4. What happens when you connect you guitar with your cable to your bandmate's amp?It sounds much louder and more powerful than mine. Is the amplifier a Fender 40W tube amp
When you connect 16 ohms cabinet to 8 ohms 100W amplifier total power is reduced to 50W, but still it should be more than enough. I've got CODE 25 and it's loud as hell.
Is your Code 25 amplifier a combo or is it attached to a cabinet?"
The Celestions in my cabinet are the G12-412ACF 12". There are 4 of them. Do you know how many decibels and power each Celestion cone provides? Another question would be, could it be that the Code 100H amp needs a higher power cabinet (for example, 200w)? Do you know if the Code 100H series requires special cabinets to deliver all the power and force of its 100 watts?
I know these amplifiers are very powerful and good, and Marshall never disappoints me, but now I'm worried because I see that in my rehearsals I can hardly hear anything from my amplifier. I think there's something not right in this whole issue. I would like, since I trust you, some solution or something with preamp, pre-fx, or volumes that I'm not handling correctly in the presets
Where could I buy cabinet CODE412?... I need some information about it. Price, technical data,.... Maybe that's the problem because my amp sounds too lower with a classic cabinet as :
Hi there,
Since mid '90 I play a JTM30 1x12 + matching C312 1x12 cabinet. How does that compare to the new ST20H Studio + ST212 Studio? Does anybody have an objective opinion for my question? I read, hear and see a lot of good comments on the new ST20 Studio series and am wondering if it would be worth selling my stuff and buy the new amp and cab.
Kind regards,
Just got a DSL 20c. When I plug the headphones into the emulator jack and put the amp on STB i don't get any output. what am I doing wrong?
hi ,
i bought a stockwell 11 mini speaker and its blue tooth has stopped working.i am trying to download update ( that i dont want) and it does not work.tried pressing button 5 and 15 seconds.what can i do?
malcolm
My code 50 amp display screen just flashes rapidly when I plug it in and turn it on with no display the amp does not work help me
