Hi 

I have a rare JCM800 bass cab from the 1980's model 1553 serial 1729 and was wondering what the standard speakers where in this model. it's currently fitted with the x2 10" Celestion K10-70 cones and one 15" Celestion Sidewinder S15-250.

where could I buy replacements if one of them failed?

thanks

Neil 

Hi,

Warranty says can register online but can find no link to register my Code 25 under MyMarshall?

Kind regards

Colin

I'm filling out the warranty card on my Code 100H and can't find the serial #. There's a number below the barcode on the sticker but the amount of digits doesn't match up with the blanks on the card. Any help would be greatly appreciated.

The iOS Gateway app was unable to connect to my CODE 50 even though my MacBook Pro is connected via bluetooth, so I did a factory reset and then tried to do a firmware update. The first part of the firmware update (1.44) appeared to install correctly. Next I saw a DSP update and tried to apply that update. In the middle of the DSP update, I received an error message to the effect that the update failed and I should power off & on my computer/device. I powered my Mac off & on, but the CODE 50 shows a progress indicator (about 20%) and says "DO NOT SWITCH OFF."

I tried to reinstall the firmware/DSP update, but this time the update process would not even begin. I suspect the  problem is the frozen progress indicator and whatever ongoing or frozen process is causing the "DO NOT SWITCH OFF" message.

Othe than ignoring the warning on the CODE 50 and powering it off & on, I don't see what else I can do. Is there a way to abort the ongoing or frozen process without turning the CODE off.

What should I do?

hallo Marshall team,

please can you tell me if the DI/Out socket can be used also with headphones?

is it confirmed that once I connected the DI/Out to a mixer PA or a Audio Interface, I can un-plug the speaker cable fro the amp without damages?

thank you

regards

Hallo,

I just purchased my new Origin head 20H and I noted a discrepancy between the rear panel speaker TAGS and the electronic manual and photo available on Marshall website. In my amp there is the socket n.2 for a mono 8 ohm connection ans the socket n.3 is labeled with a dotted line to the n.2 for the connection of a pair of cabinet 16 ohm. while in the Marshall web site the sockets n.2 and n.3 are labeled with 8 ohm. Could you Clarify please? thanks.

After have all try, can you tell me wich phone are you sure that turns right with Getaway ?

Hi,

I have a problem with my new Stockwell II. It plays the Bluetooth connection sound while playing music with my iPad Air, which is only 10 centimeters away.

The intervall between this sounds is not constant, between 30s and 15 minutes. But quite annoying. Music playing is not interrupted.

Any ideas what to do? Maybe a firmware update? (But my windows 8.1 pc doesn't recognize the speaker.)

Thanks!!!

tenho code25 eu atualizei ele quando eu ligo ele nao aparece mais o logotipo da marschall tem algum problema.ele esta funcionando normal.

It's not happening always, but when it does it's frustrating.  Also, sometimes the volume (when it's only cranked up around 2) it tends to get quiter than how louder it suppose to be. Should i bring it back to the shop and ask a repair?

Hi. I recently purchased a DSL40 CR and am wanting the 6 button footswitch so I can use all of the amps capabilities. Is the PEDL 91016 available yet in the US? My local Marshall dealer says that these have been back ordered for months. Currently they are telling me there is a 2 to 3 week shipment delay. What is the availability of these?

Not a lot honestly. I've had a 50 watt Marshall DSL head for about 6 years now, and it's been wonderful.

The thing is, Marshalls do the Marshall sound very well. But people do not have the space to make the Marshall come alive. Even 50 watts is way too loud to cut loose and open it up to a really nice saturated volume. To keep up with the br00tal metalz times, Marshall has been increasing the preamp gain stages. I have 4 preamp tubes in my amp, and it has way too much gain on tap. Preamp gain will always sound fizzy and harsh compared to poweramp gain, and Marshalls produce way too much volume to open up the poweramp to a nice tonal level, especially in the era of excellent PA systems and great microphones

I think that a lot of folks throw money at the problem, buying independently built amps made with period correct caps and resistors, PTP wiring, etc. But the differences are marginal at best when comparing two identical circuits (mathematically speaking) build with the types of parts used at Marshall vs. NOS stuff by indie builders. I honestly think half of the appeal is placebo effect. Players fool themselves into thinking their indie build JCM800 copy sounds sooooooo much better than a newly made JCM800 from Marshall. They're the same, any difference will come down to the speakers, microphones, PAs, and guitars used.

Hi! I have an issue while trying to transfer dowloaded presets to my Code25. It occures both usb and bluetooth connections.  On a usb connection i click the “amp” icon on a preset, it’s name appears on a Code screen. I push and hold store button on amp, “saved” appears. But then Code becomes freeezed, it does not react on button push etc. when i switch it off and then switch on it works fine, preset available on amp. The same issue appears when i try to transfer presets using Gateway app. What I do wrong?

Hello everyone,,

Hello,

I am experiencing some troubles with the battery of my speaker stockwell that I bought 2 years ago.

I would like to know the contact phone number of the technical service in Valencia (Spain).

Thanks.

Dear all,

I am experiencing some trouble with my Minor II headphones, as they do not connect anymore. Tried to pair them again, but they do not appear on my iPhone (7).... when switching on, the white light constantly flashes to green, but I cannot find any info about a green light.

Thanks for Your response, but  i wanted To insist that popping Is not produced by the buttom, it is through The MX 212a speaker's cabinet, i have compared To other amps DSL And don't  have this problem. Please help me..

Hello All,

What cable does someone use to hook up their ipad to a Code 50? it would a lightning to a ???

And why does one need a cable to  hook up to the Code? if the Code is synched via blutooth then anyhting on the APP, such as updates or presets, should also be able to get tot he Code via the blutooth and not need a cable. Could this be a glitch on Marshall's end or  they just never programmed it into the software to do it. Seems like an oversight, no? 

Thanks for any help anyone can give,

Lou

Does anyone know of a good preset that would sound like the song “I’m Alright” by Neil Zaza?