Just found out Kilburn is being scrapped at the end of the year - so that means there will not be a Kilburn 3 - see this post here:
reddit.com/r/Bluetooth_Speakers/s/eezEtlnT70
Why are you doing this?
Hello! Do you have any idea where I could find a fitting button to replace a missing one?
Bonjour
Quelqu'un aurait il la notice détaillée du DSL 5 CR s'il vous plaît?
Merci d'avance
cant download presets to gateway cant sync from gateway to my phone or ipad. Whats the story?
I've recently bought the DSL1-CR and i want to praticse with headphones, but if plug them to the emulated output the sound comes out from the speaker, i decided to check on the instructions where there is written that in case of i have the DSL1-HR i must umplug the speaker from the amp, but there are no information about the CR.
Can you help me?
Regards,
Lorenzo.
I use the CODE 100 H. My question would be the following: I have configured some settings within a preset to play a song, but when it comes to the guitar solo, how can I increase the volume for the solo? And how can I reduce the volume after the solo? Do I need an external booster pedal? Do I have to have two different presets for the same song in order to have a separate volume for the solo? I hope you understand my question. I don't know how to increase the volume when I'm playing a song with a preset within the bank, when the guitar solo comes in. Do I need to configure two different banks, two different presets, or can I do it within the same preset? I hope you can help me. Thank you very much.
Firmware up to date, factory reset(s) done but still goes dead within a minute or so. It will occasionally let you play but not change the preset (as that makes it cuts out).
Has done it for a while but I don't use it often - any suggestions and how long is the warranty in the UK?
Salve, ho un Stanmore 1 una volta fatto l abbinamento non riproduce il suono cosa può essere? Grazie
Have an Iphone cannot get it to pair with my new code 50 amp????????
Already looked on Youtube for answer and that didn't work??????????????????
My new JTM45 acts strange on the input side. The two top inputs are supposed to be normal sensitivity and the two bottom ones lower sensitivity. On mine the two top inputs are just lower level, less treble versions of the bottom two inputs. Just sounding dull and lower level. Also, jumping the 1&2 inputs does not work. When jumping, channel 1 takes over and channel 2 almost does not add anything (just a tad) even when the normal loudness level is set to max (and the high treble loudness level is still low). What can I do?
When I plug in footswitch nothing happens no light anything tried another cable nothing both cable work with guitar so I'm thinking not cable
I have a DSL40cr. I also have an 8 ohm (2x12) cabinet. The DSL40 onboard speaker is plugged into the 1@16 ohm input. When I run my 8ohm cabinet (plugged into the 1@8ohm output), can I run the onboard speaker at the same time, or do I need to unplug it? Asked another way, can I run the onboard 16ohm speaker and the 8ohm (2x12) cabinet at the same time?
Hello folks,
I´m looking for the building date of my DSL40C. Not sure to understand the label code right. Here are my Labelnumbers V01061659E and also 12-16 on the right side of label. I hope someone could help. thx and greetings from germany, Benno
bonjour ,
je n'ai plus acces a internet depuis mon telephone/avec l'aplication gateway/
j'ai 40 presets memorisé ,
Hallo, Freunde von Blues & Rock,
ich bin hier neu auf My.Marshall.com. Ich suche für den soeben neu gekauften Amp MG50GFX nach Manual und Datenblatt mit technischen Daten und möglicherweise ein Diagramm der Schaltung, Dasselbe suche ich auch für den viefach-Fußschalter "Stompware for MG".
Ferner suche ich Rat bei einem Sound-Problem. Liegt meine eingeschaltete Superstrat etwa einen Meter vor dem eingeschalteten Amp, so höre ich ein störendes Brummen (50Hz). Witzig ist dabei aber: mit dem 5-Wege-Schalter der Gitarre kann ich das Brummen ein- und ausschalten. Besonders deutlich brummt es, wenn ein Single-Coil-PU auf solo geschaltet wird. Der Humbucker macht hingegen genau das, was man von ihm erwartet: Er unterdrückt das Brummen,
Was kann man dagegen tun? Entstörfilter in die Signal-Chain einbauen? Abschirmung der Gitarre gegen störende Induktion verbessern (Faraday'scher Käfig) ?
Herzlichen Dank im Voraus
FarrierPete
------------------------------------------------------------------------------------------------------
Hello, friends of Blues & Rock,
I'm new here on My.Marshall.com. I'm looking for a manual and datasheet with technical data and possibly a diagram of the circuit for the MG50GFX amp I've just bought. I'm also looking for the same for the "Stompware for MG" multi-function footswitch.
I am also looking for advice on a sound problem. If my switched-on Superstrat is about one meter in front of the switched-on amp, I hear an annoying hum (50Hz). The funny thing is that I can switch the hum on and off with the guitar's 5-way switch. The hum is particularly noticeable when a single-coil PU is switched to solo. The humbucker, on the other hand, does exactly what you would expect it to do: it suppresses the hum,
What can you do about it? Install interference suppression filters in the signal chain? Improve the guitar's shielding against interfering induction (Faraday cage)?
Many thanks in advance
FarrierPete
for my dsl20cr
Does anyone know the actual model of the speakers that are used in the CODE412 cab? I wanted to find out before I ended up taking the back off to have a look as there are no details online?
Cheers.
Bonjour
Après toutes les manipulations détaillées du sav. .Pas moyen de rétablir un son correct .
Depuis plus de nouvelles ???
Des crépitements se font entendre et le volume max est très faible.
Elle est neuve et donc garantie. Recu en cadeau avec un téléphone honor .
Comment dois je faire pour une prise en charge svp?
Help me please
How can I delete my account?
I can't find a way to do Thatcher or contact Marshall abortus it.
The effects loop on my Origin 20 head is not working and I can't figure out why. Any suggestions? The footswitch is plugged in and the boost switch works but no pedals work in the loop. All cables and pedals tried are in working order as I tried them with another amps effects loop and it worked fine.