Hi, is there anyone who is able to create a preset (patch) to get the sound of the Peavey Delta Blues out of the Marshall code 100 ?

Thanks.

Christiaan

I mean probably i could make something like a fuzz pedal but it would be great if the amp alredy had one

Hello TEAM MARSHALL.

I'm curious about something:

It only ocurred to me last night that maybe, just maybe, replacing the Master Volume (and in my case, on one of my five amps. also the Preset Volume) pot. with a new or replacement (generic, higher quality) pot. would solve this Master Volume issue once and for all.  So to this end I started scouring the Internet only to find that there is not a single supplier that I can find that supplies spares for the CODE amps.  There's spares for just about every other Marshall amp. known to man (including the MG series) but nothing, nada, for the CODE amps.  and this INCLUDES the Marshall store itself.  Your input and thoughts on this???

Also: how difficult would it be to obtain the specs. etc. of the amps. e.g. what are the specs. of the pots. (particularly the Master Volume and Preset Volume pots.)???

Regards,

Dale.

Hello, I would like to connect one of my PCs (OS linux) on a Marshall CODE 50 and take control via usb midi.

When I open /etc/dmmidi2 in read acces. Reading file char by char, I see information when I touch the buttons of the amp (PREFX, AMP, MOD, ...). I can find the information in CODE-Midi-Implementation-Chart-V2.1.pdf.

I usually get two or three bytes and cross it with the document.
But this frame is not in the form Start of Transmission> Header> Command> End of Transmission.

By against when I open /etc/dmmmidi2 in write access, I can not send any command.
After having turned on the amp, I sent the following sequence for RECALL PRESETS 05:
0xF0 0x00 0x21 0x15 0x7F 0x7F 0x7F 0x73 0x01 0x05 0xF7
or RECALL CURRENT SETTINGS:
0xF0 0x00 0x21 0x15 0x7F 0x7F 0x7F 0x72 0x01 0x00 0xF7
Start of Transmission> Header> Command> End of Transmission
This command does not seem to work. Is there an intermediary step?

Would it be possible to give me a typical sequence to the CODE or a document that will explain the procedure to operate (ON / OFF) one of the button (PREFX, AMP, MOD, ...) of the amp.
Thank you in advance.
Cordially.

yoann

hola a todos alguien tendria para pasarme como configurar un preset Joe satriani

hi coud you send me a presset joe satrian

TKs

Hi,

The problem that i mentioned in the title hapenned after adding presets to my library and now i can't use the button "sync now"

How can i make the app synchronize whit the cloud?

I've had a great time demoing the presets but once I save one I like into 'My Presets' and add it onto 'My Gateway' list I can't get it to go over onto my amp.

Can I use the USB to put the patches/presets I want directly onto my amp or do I have to go through the Mobile App to sync it?

Hello,

Yesterday I received my Code 50 amp. I played some hours with it and there is 1 thing that i noticed. I play most of the time at home through a headphone because neighbours, and the presets aswell as some own created sets sound really muffed if I add any Cab. I tried diffent Cabs but for me it sounds way clearer without a cab model.  I was wondering how this is possible? Did i miss something? When I remove the cab from a preset add lower the presence by 2 it sounds so much better

And when playing through the speaker while gigging with friends, will this difference still be there or is a cab model "necessary" when playing through the speaker?

Greetings, Tom

the chorus on my Code 50 is not working. I’ve had the amp about half a year, but not really used the chorus until recently. 

If I turn the chorus on, the sound changes a little bit, but it’s not a chorus sound – although the speed option has an effect. 

If I switch between CLS and VIB a few times, sometimes the chorus will suddenly kick in, and sound good, but if I turn it off or change presets, the chorus reverts back to its barely-there sound. 

Has as anyone else suffered from this? Any tips? Thanks. 

I recently added the tuner to my footswitch (preset), but now I want to undo it. I'd rather have the first bank available for a pre fx- preset. Doe anybody know how to undo it, ig by resetting the footswitch to factory settings?

thanks

Hello all,

I have had my Marshall CODE 50 since last summer with no issues whatsoever...until now.  Today when I decided to turn on my amp it was going NUTS.  Whenever I turned up the Master dial my presets kept changing rapidly on their own and the amp would not output sound whatsoever.  I tried updating the system's firmware and even performed a factory reset but nothing helped.  Has anyone experienced a similar problem?  Any advice or help in the right direction would be greatly appreciated.

hey Team Marshall,

I have the foot controller and a Code 50. Dig them both, GREAT AMP!! How do I over write a stored preset on the controller. Ex: on A1 I have DSL CLEAN I want to assign the TUNER to A1 then on A2 assign DSL CLEAN. 

Hello,

How can I program my code 50 so I can switch up/down through all my 100 presets?

I am using a 2 button footswich. Connected to a code 100H it worked fine.

Hey Folks,

New here ... how do I get the presets I have stored here on the web site "library" to show up on the "library" I have on my Gateway app?

Thanks in advance

How can you try out a new PRESET without overwriting a PREST on CODE 50 or the GATEWAY Library?  jwaldron007@optonline.net

Has anyone found a preset or come close to she sells sanctuary by the cult sound. !

can any one help me i can't down load any of my favorite guitar players presets,do i do it manually on my phone or what i got how the USB gets the music from my library,but every time i pair my phone with my marshall it stays on for one preset i can't even reconize so i play all my music songs pink floyd led zepplin SRV JIMI H On simple clean setting what the  ,and futher more at a guitarist presets he might have used at the left bottom corner there is 4 or 5 boxes,phone box amp box and stupid finger sign and so on but i get a stop sign code when i click on the little amp .i can play little wing and basically with an amp that should tell you more i guess its not the amp or the guitar you have its the size of the theory of how your soul connects with the vibe.help if you can

I am wondering if anyone has a preset that will work for using an external effects pedal into my Code 50? I only want to run the external effects (distortion, reverb, delay) and nothing fromthe amp itself. What I am seeing is that even with all effects (amps, modeling, etc.) turned off on the Code my pedal into it sounds like garbage. Very muffled, bassy, and muddy. I have the EQ on the amp set so that the bass is all the way down and mid/tebble are all the way up and it still sounds terrible. I don't want to have to edit and mess with every patch on my old Zoom GFX8. The pedal doesn't sound like this into my old 40 Watt Fender bassman.

Any advice on setting up the Code to sound good with external effects would be greatly appreciated.

Dear Marshall Team,

I have an idea for expanding the Gateway program, for a panel with "favorite" few presets. This idea is primarily intended to use the Gateway program in an easy way during performances. At the moment, switching between used presets is relatively difficult if we want to do it quickly, just like during a concert. If you added such a panel, you could set several favorite sounds, and choosing them would be very fast, using large buttons.

Please let me know your opinion.

best regard

Hi, Is there a way to reduce the power on a Code 25 from 35w down to 5w or 1w like you get on modelling amps from 'other' manufacturers?

To use as a practice amp in my home, I'm having to set the master volume and volume controls really low on the amp and still dial it back on the guitar to the point it is affecting the tone of the preset.

Since this was not obviously available on the top panel, I wondered if it was available via the app but I can't find it if it is.

Thanks in advance.