Questions
Showing results 161 to 180 of 4079
0

votes

0

answers

218

views

Hallo, Freunde von Blues & Rock,

ich bin hier neu auf My.Marshall.com. Ich suche für den soeben neu gekauften Amp MG50GFX nach Manual und Datenblatt mit technischen Daten und möglicherweise ein Diagramm der Schaltung, Dasselbe suche ich auch für den viefach-Fußschalter "Stompware for MG".

Ferner suche ich Rat bei einem Sound-Problem. Liegt meine eingeschaltete Superstrat etwa einen Meter vor dem eingeschalteten Amp, so höre ich ein störendes Brummen (50Hz). Witzig ist dabei aber: mit dem 5-Wege-Schalter der Gitarre kann ich das Brummen ein- und ausschalten. Besonders deutlich brummt es, wenn ein Single-Coil-PU auf solo geschaltet wird. Der Humbucker macht hingegen genau das, was man von ihm erwartet: Er unterdrückt das Brummen,

Was kann man dagegen tun? Entstörfilter in die Signal-Chain einbauen? Abschirmung der Gitarre gegen störende Induktion verbessern (Faraday'scher Käfig) ?

Herzlichen Dank im Voraus

FarrierPete

------------------------------------------------------------------------------------------------------

Hello, friends of Blues & Rock,

I'm new here on My.Marshall.com. I'm looking for a manual and datasheet with technical data and possibly a diagram of the circuit for the MG50GFX amp I've just bought. I'm also looking for the same for the "Stompware for MG" multi-function footswitch.

I am also looking for advice on a sound problem. If my switched-on Superstrat is about one meter in front of the switched-on amp, I hear an annoying hum (50Hz). The funny thing is that I can switch the hum on and off with the guitar's 5-way switch. The hum is particularly noticeable when a single-coil PU is switched to solo. The humbucker, on the other hand, does exactly what you would expect it to do: it suppresses the hum,

What can you do about it? Install interference suppression filters in the signal chain? Improve the guitar's shielding against interfering induction (Faraday cage)?

Many thanks in advance

FarrierPete

 

asked 29 Apr 2024 at 11:51 AM

Peter Seyfferth
0

votes

0

answers

165

views

Hola, los altavoces Acton II y Stamnore II también los puedo registrar?

asked 28 Apr 2024 at 10:06 PM

ANDRES RESTREPO
0

votes

1

answer

275

views

Just found out Kilburn is being scrapped at the end of the year - so that means there will not be a Kilburn 3 - see this post here:

reddit.com/r/Bluetooth_Speakers/s/eezEtlnT70

Why are you doing this?

edited 28 Apr 2024 at 12:25 PM

Don Cart

asked 28 Apr 2024 at 12:09 PM

Don Cart
0

votes

0

answers

180

views

How can I delete my account?

I can't find a way to do Thatcher or contact Marshall abortus it.

edited 28 Apr 2024 at 08:48 AM

Hans de Groote

asked 28 Apr 2024 at 08:47 AM

Hans de Groote
0

votes

1

answer

230

views

I use the CODE 100 H. My question would be the following: I have configured some settings within a preset to play a song, but when it comes to the guitar solo, how can I increase the volume for the solo? And how can I reduce the volume after the solo? Do I need an external booster pedal? Do I have to have two different presets for the same song in order to have a separate volume for the solo? I hope you understand my question. I don't know how to increase the volume when I'm playing a song with a preset within the bank, when the guitar solo comes in. Do I need to configure two different banks, two different presets, or can I do it within the same preset? I hope you can help me. Thank you very much.

asked 27 Apr 2024 at 02:48 PM

xavi Fernández Gaya
0

votes

1

answer

191

views

How do you use the compression and distortion effect at the same time

asked 25 Apr 2024 at 11:27 PM

marshall marshall
0

votes

1

answer

206

views

Hello folks,

I´m looking for the building date of my DSL40C. Not sure to understand the label code right. Here are my Labelnumbers V01061659E  and also 12-16 on the right side of label. I hope someone could help. thx and greetings from germany, Benno

asked 25 Apr 2024 at 10:46 PM

Benzino Bussmann
0

votes

1

answer

343

views

Bonjour

Quelqu'un aurait il la notice détaillée du DSL 5 CR s'il vous plaît?

Merci d'avance

 

DSL

edited 25 Apr 2024 at 08:26 PM

François FRANCOIS

asked 25 Apr 2024 at 08:21 PM

François FRANCOIS
0

votes

0

answers

163

views

Bonjour 

Après toutes les manipulations détaillées du sav. .Pas moyen de rétablir un son correct .

Depuis plus de nouvelles ??? 

Des crépitements se font entendre et le volume max est très faible. 

Elle est neuve et donc garantie. Recu en cadeau avec un téléphone honor .

Comment dois je faire pour une prise en charge svp?

Help me please

 

 

asked 24 Apr 2024 at 12:29 PM

Guillaume Guillaume
0

votes

1

answer

186

views

Does anyone know the actual model of the speakers that are used in the CODE412 cab? I wanted to find out before I ended up taking the back off to have a look as there are no details online?

Cheers.

asked 24 Apr 2024 at 09:08 AM

Rick Green
0

votes

1

answer

207

views

Wondering if anyone has had or heard of this issue?

 

Code50, less than a year old.

 

Me and a buddy are somewhat beginners, and playing Deftones and Chevelle type songs. I have a "Deftones style" distorted heavy tone preset loaded that I'm playing on.

 

So after an hour or so playing, the tone will start to sound "metallic" and kind've have a "ping" to it, if that makes sense. Sort of sounds like you have a speaker inside of a giant metal cup.

 

Sorry if this is a newbie question, just sort of confused.

 

The guitar was new in October, so I assume it's not the strings. I also tried swapping to my Jackson guitar, same annoying metallic pingy sound when strumming. Changed the cables too.

 

Any ideas?

edited 24 Apr 2024 at 12:12 PM

Matt Winter

asked 24 Apr 2024 at 12:40 AM

Matt Winter
0

votes

3

answers

208

views

Firmware up to date, factory reset(s) done but still goes dead within a minute or so. It will occasionally let you play but not change the preset (as that makes it cuts out).

Has done it for a while but I don't use it often - any suggestions and how long is the warranty in the UK?

asked 23 Apr 2024 at 02:53 PM

Jon Dimmock
0

votes

1

answer

421

views

Salve, ho un Stanmore 1 una volta fatto l abbinamento non riproduce il suono cosa può essere? Grazie 

asked 21 Apr 2024 at 04:24 PM

Antonio Bosco
0

votes

0

answers

168

views

for my dsl20cr

asked 20 Apr 2024 at 09:18 PM

Glenn Starbird
0

votes

1

answer

267

views

I have a DSL40cr. I also have an 8 ohm (2x12) cabinet.  The DSL40 onboard speaker is plugged into the 1@16 ohm input.  When I run my 8ohm cabinet (plugged into the 1@8ohm output), can I run the onboard speaker at the same time, or do I need to unplug it? Asked another way, can I run the onboard 16ohm speaker and the 8ohm (2x12) cabinet at the same time?

asked 20 Apr 2024 at 08:34 PM

Robert Tice
0

votes

2

answers

213

views

Have an Iphone cannot get it to pair with my new code 50 amp????????

Already looked on Youtube for answer and that didn't work??????????????????

asked 20 Apr 2024 at 06:38 PM

Joseph Daugherty
0

votes

1

answer

230

views

My new JTM45 acts strange on the input side. The two top inputs are supposed to be normal sensitivity and the two bottom ones lower sensitivity. On mine the two top inputs are just lower level, less treble versions of the bottom two inputs. Just sounding dull and lower level. Also, jumping the 1&2 inputs does not work. When jumping, channel 1 takes over and channel 2 almost does not add anything (just a tad) even when the normal loudness level is set to max (and the high treble loudness level is still low). What can I do?  

asked 19 Apr 2024 at 08:04 AM

Mr Bluey
0

votes

1

answer

195

views

Hello.

I had that issue for a sometime on my code50 but now I know a bit more  about it.  For at least two years  this amp was changing preset settings why I was playing on it  At first I did not reallise  that especially on clear sound, but after some time with distorted sound  it was obvious that sound become louder and more distorted. Visually I could see that display become dim and almost always was changing from number and name  page of the preset to page with settings.  Now I can see when phone is connected settings on the app are changing as well. It is gain, volume, bass, middle   and treble  parameters which move up. Master is staying like it is. After changing preset to other one and coming back to the same preset it will stay normal for some time (few second to few minutes) and change again.

I tried to update firmware but that did not help. For some time I was suspecting power supply issue as sometimes  electricity in my place can be not up to standar , but now  I am sure that is not a case.  Any idea what cause that problem and how to fix it?

asked 18 Apr 2024 at 02:38 PM

Raff Von D
0

votes

0

answers

209

views

Hello! Do you have any idea where I could find a fitting button to replace a missing one?

DSL

asked 17 Apr 2024 at 07:39 AM

Timo Mankki
0

votes

2

answers

246

views

good morning I purchased a marshall code 50, I immediately updated the firmware to version 1.48, I performed all the possible procedures for connecting to the phone, when I press rev and pover it goes into pairing mode and the blue light flashes but no phone that I have tried and sees it in the devices, is there a solution for this problem?

asked 17 Apr 2024 at 05:09 AM

luca landi
Showing results 161 to 180 of 4079
Loading - please wait...
This site uses cookies to improve your experience. By continuing we assume that you're ok for us to store cookies on your device. You can change your cookie settings at any time, or delete cookies, by going to our cookie consent page.