I have an Axe Trak insulated speaker (here is a link to info on the speaker) www.axetrak.com/guitarmanual.pdf

When I have run it from the Marshall it has cut out after playing for a while, I have turned off the amp and then the following day used the amp with its built in 12" speaker and it has been fine. When i read the JTM 60 manual it said it is fine to drive a 8ohm from the external speaker output ONLY, not the internal out connection.

Is this OK? when things cut out it makes me worry about my Marshall and I really don't want to cause it any damage.... Also I have checked the speaker lead and that is all good, when it cut out it the sound broke up and faded in about 1 second. It is the 2nd time is has happened so i thought I best get some advice. The Axe Trak is great and means i can play a valve amp and get valve amp tone and not disturb my neighbours, it is a great bit of kit for home recording and I want/need to be able to use it. Any advice?

Thanks, Robin..

I guess with Marshall being a small company without much expertise in building amps, this should be expected.  Maybe once they've been around a while and get the hang of building amps then they'll be able to release products that work as advertised and that they are also able to maintain and provide support for.

Hang in there Marshall, you'll be a good amp company someday!

I have successfully synced some presets onto the Gateway App on my phone and can use them when my phone is connected to my Code 50 amp via bluetooth. Is there anyway to overwrite the presets on the amp with presets on the Gateway app, so those presets are available without connecting to my phone? Thanks!

I recently bought a MXR Talkbox and was wondering if the code 100 was compatible with the talkbox 

When switching my DSL-40 from 40watts to 20watts ,the 20watt mode has a loud defining squeal .I don't know what is causing it.

I connected my Code 50 to my laptop via bluetooth, but the my.marshall presets says "CODE not connected". I tried connecting via USB, but the amp has a goofy connector that standard USB cables do not connect to. Also - I can connect via the Gateway app on my phone, but the presets I add to My Library do not show up (even though it says that they have synced). 

Hi there! I recently bought my code25 but when i try to download the app it says that my device is not compatible. I have a samsung galaxy A5. is there any known issue with this particular device? The mobile has all the requirements (latest updates, enough memory etc) and i also followed the steps posted on similar posts. Is there any way that i could get the app to download? Thank you in advance

Hi!

I am desperately trying to imitate Robert Smith’s sound, from the Wish era and more specifically their live appearances of the time (Show, Paris)

You can hear this to know what I mean
https://www.youtube.com/watch?v=hnVldyHRcjU

 Can anyone suggest any setting for Code 50? I would really REALLY appreciate it!

Thanks in advance!

how do I play over a part that I have looped .?

I have connected several devices via bluetooth to code 50, but it did not manage to  synchronize whit the app.

Help... 

Hi

How do I delete my My Marshall profile?

Thanks.

Hoswit,

Loving my code 100h, surely marshall will be creating more stomp boxes in future, can code users expect updates to the fx chain?

I'm connected through bluetooth to my code 50 and i can choose to change the different presets, but when i go to edit the presets of gain, bass, treble, volme etc etc, nothing hapens. Am i missing something? Even that little button the shows phone to amp or amp to phone in the bottom left corner does nothing.

cheers

Hi.

Just a warning (possibly more a bit of advice maybe):

I noticed over the weekend that sometimes (not always) when retrieving a patch from a CODE amp. the Marshall CODE PC Editor does not always get it right.  Sometimes it will load perfectly and other times it's almost as if it's retrieved some, not all, of the settings for the patch.  I only noticed this after retrieiving some presets, making a change or two, and then overwriting on the amp. with the incorrect settings and I thought I was going bonkers because I checked and re-checked what I was doing but whenever I saved on the amp. sometimes one or two of the parameters were not as I set them.  It seems to do the same when loading a saved patch from disk too.  Wasted hours!!!

Anyway: the easy workaround really is to just keep clicking on the retrieve button until there are no more changes to any of the parameters of the preset being shown on the screen (normally only need to do it twice but three is a lucky number).  Make your changes then save back to the amp. (I've resorted to doing this three times too just for safety sake).  And when loading from disk: get into the habit of doing it three times too!!!

I'll try get their support to have a look at it (although things seem every so quiet over there).

I mention the above because even although we all know the this is not a Marshall Amplication PLC product and is not supported by them: it is indeed punted on these forums quite widely (by myself too).

Regards,

Dale.

hi ,marshall,need ,asio drivers,i use reason 10,it does not recognise it,if i knew this i would have,kept with my boss gt-1,this is frustrating!!!!,anyone?? thanks!

Hi can anyone advise how i connect My 2018 iPad. Thanks in advance Tony.

Not a question, just a general observation for discussion. 

I've heard a lot of people saying they can only use a CODE 25 for home use with the master volume set at 2 or 3 .

The amp sounds much better with the master volume at 8 and the guitar volume set very low (using a Les Paul).  

The amp sounds much fuller and more responsive.

Hi, i have a Marshall Code 50. I tried to record with usb input but there is a lot of noise (interference) every 10-15-20 seconds (random).

I have high quality cable and a yamaha RGX A2. With the oldest firmware version it was noisier, now with the v1.41 is better but how can I fix?

Any suggestions?

Sorry for my english.

Thank you.

Hi,

I own a Code 25 amp and my footswitch started doing weird stuff recently.

It keeps on turning on and off, even though its connected to the amp with a cabel,

I tried using a diffrent cable (the one that came with the footswitch), but the same happened.

Can I do something to make it work again?