Questions
Showing results 3041 to 3054 of 3054
0

votes

1

answer

721

views

Is my bluesbreaker a series ll model? The serial number is 1999-48-0866-AG

asked 09 Jun 2016 at 07:13 PM

Andrew Wetherall
0

votes

2

answers

4k

views

Hello, I purchased the DSL40C and MX212 Cabinet. I know the Speaker in the combo is 16-ohms. I also know the speakers in the MX212 are wired for 8-ohms. I know if I use the cabinet, I can't use the speaker in the combo together. My question is, has anybody ever put an 8-ohm speaker in the combo? I am thinking that two 8-ohm loads would give me a 3x12 config for extra beef! Would this work, and would the amp still sound just as good if I used it alone (to take to jam sessions) on the 8-ohm output? Thanks   

edited 09 Jun 2016 at 06:42 PM

Tommy Scott

asked 09 Jun 2016 at 06:40 PM

Tommy Scott
13

votes

1

answer

1.4k

views

Hi why was the code amp released when it is imposssible to get a 91009 foot swich anywhere also no covers avalible to protect said amp. I am being told up to october on the swich and who knows on the covers. can you help.

asked 09 Jun 2016 at 02:45 PM

Steven Greenway (13)
0

votes

2

answers

1k

views

whereis the serial number located on my MG100HCFX amp?

 

asked 08 Jun 2016 at 11:18 PM

charles hemphill
0

votes

1

answer

926

views

Is there a printable Code owner's manual?

asked 08 Jun 2016 at 09:03 PM

Michael Robertson
0

votes

1

answer

1.1k

views

Could you give me a rough age of My JTM45 Lead - Serial appears to be S5002

Cheers

Mike

 

 

asked 08 Jun 2016 at 12:48 PM

Mike O'Shannessy
0

votes

1

answer

1.2k

views

Hello, I know this has been covered here and I have read all of the messages, but I would like some newer feedback regarding my newly purchased DSL40C implimented with a Line 6 POD 2.0.

I realize you can't shut off amp modeling and that to achieve the least amount of colorization, and preserve my Marshall tone as much as possible, I should set the POD 2.0 to Tube Preamp, and EQs to 12 o-clock, which shuts off Cabinet Simulation.   I want to use the POD 2.0 because it has a bunch of presets I use, which I will modify and it gives me multi effects with a Pedal. 

How should I route this, given the effects send on the DSL40C is probably line level, and has no attenuator. The POD 2.0 has instrument in and I presume Instrument out. I know it will run -10 and +4 when using TRS. I will say I don't see any documentation on the DSL40C loop. 

This is my first Marshall setup and need advice from you gurus.

Any and all advice is appreciated.

Thanks so much!

 

 

 

 

 

asked 07 Jun 2016 at 11:43 PM

Tommy Scott
1

vote

1

answer

1k

views

I updated the gateway app 5 minutes ago to latest version - my phone is an moto g (gen2) running android 5.0.2. The app worked sort of ok on previous version but now its giving a message as follows.

      "Screen not supported - tThe minimum screen size is 640x960" 

From what I can see under the message though looks to me ok I can see "00 EL34 Heaven" and all the initial presets not covered by the message but thats it nothing works so I guess thats it after about 2 and a half weeks of being apple to control from the app I now find that I cannot do anything from the app.

 

Any ideas what I need to do next.

asked 07 Jun 2016 at 03:02 PM

Alan Unwin (12)
0

votes

1

answer

815

views

hi site does noy reconize my model #MG15HCFX ? HOW COME?

Michael 

asked 06 Jun 2016 at 01:02 AM

Michael Christopher
0

votes

1

answer

1.7k

views

Is the speaker in the Code 25 a full range speaker and if not, will there be clipping issues streaming music into the amp while playing my guitar?

 

Thanks

asked 05 Jun 2016 at 04:09 PM

Mark Stevens
0

votes

1

answer

915

views

Hi,

Can I check with you do I need to register my new Marshall headphone mode EQ? If so how do I do it?

Regards,

Chin How

asked 05 Jun 2016 at 02:56 PM

Tan How
21

votes

2

answers

2k

views

Hello, I've noticed that the firmware update is only available for windows not mac. Is there any alternative way mac users can update? Or will this be an option in the future? 

 

Many thanks

edited 04 Jun 2016 at 05:08 PM

Jonathan Leach (20)

asked 04 Jun 2016 at 05:07 PM

Jonathan Leach (20)
0

votes

2

answers

958

views

The Amp model 2555x doesn't exist... Or I put wrong product code for this amp (begin with 255...) ? 

Thank you ! 

Best regards, 

Max

asked 04 Jun 2016 at 08:50 AM

Maxence Duhayon
0

votes

1

answer

946

views

Hello. I have a marshall mkii lead head that I've had since I was young. The serial number is 9941L and I was trying to find a new power transformer for it. Can you help? Thank you.

edited 03 Jun 2016 at 10:00 PM

Tom kleppick

asked 03 Jun 2016 at 09:59 PM

Tom kleppick
Showing results 3041 to 3054 of 3054
Loading - please wait...