NEEDED RESPONSE FOR LOW MARSHALL REF VL VE00051 WHERE YOU CAN GET IT. COULD ANY HELP ME.

Hi, i am using a code 50, and i cannot store the vlume levels in presets.

I am using 3 diferent presets, but i cannot level the volumes, i think that CODE dont store that.

How can i solve this ?? Its very importan, otherwise its a complete mess....all the presets with diferente volume levels....

Please HELP ME !!!

Thanks

Hello guys,

I recently purchased a Year model 1973 50 watt Plexi head and wanted to replace the knobs on the amp.  The current knobs have set-screw knobs. 

Question:  Do the push-on replacement knobs fit properly on the shafts?  Or do I need to replace with set-screw knobs only?

Thanks

Victor

Hi 

This is more of a warning than a question -

I made the mistake of buying a used JVM210c on ebay -  it was problematic from day one. I spent well over a $1,000 on repairs over the course of a year.

I finally found a tech who knew what he was doing - turns out the JVM210c has issues with the preamp pc board. The amp sounds greats since the board was replaced and have had no new issues.

I don't know how widespread the issue is but make sure you get a good warranty before you buy.

Please add firmware version number, date and release notes  

Today I tried to connect my guitar via iRig and a common audio cable to my Code 50.

The sound was really muddy without any treble... Same when I play music from my phone over the audio input... 

Can anyone confirm this?

And is there a way to control the input volume?

Thanks and regards 

Seb

THIS ISSUE IS STILL ACTUAL !!!  THE MASTER VOLUME ADJUSTMENT IS NOT LINEAR !!! PLEASE MAKE A FIRMWARE UPDATE TO SOLVE THAT !!!

When is the next scheduled firmware update for the CODE25?  

When was the most recent one ?

Thanks!

The CODE Footswitch manual is not very informative.

I watched all the youtube videos I could find on it but I'm still confused on how some of the functions operate.

Can anyone provide me with a link to a more comprehensive document?

Thanks,

just got an iPad Pro through my job and would live to try and record my code 25 using the micro usb output. Anyone know how I can do this? Does anyone make a cable with a male micro usb on one end and a male lightning connector on the othe end? Do I need a specific interface or can I use some kind of adapter? Can't seem to easily find anything on the ole interwebs about how to do this. TIA. 

how do i download patches from amp to computer...it says my password is incorrect

Especially on low strings, low notes.

Worse on neck pickups.

JTM45 especially bad.

Or is it just that my guitars have hotter pickups? Then again, some of my neck pickups aren't that hot and even switched to single-coil, it gets muddy and boomy.

The settings don't really help. Tried changes on all settings... EQ, cabs, preamps, amps, presence, resonance, you name it.

Or is it because I play at room volumes? Still need to try a headphone to see if it's speaker or emulator...

Please add version numbers and details to firmware page so that we know what we are in for.

my '72 50 watt doesn't have the output it used to have. Also breaks up way too fast. I'm using a boss overdrive ( same combo i've used for 30 years) and even with the gain on the pedal turned way down it's super satuated with too much distortion, high end and almost no low end. 

hi! i want to add an external cab with 1x12" celestions vintage 30, what will be the speaker requirements and the steps to connect it. thank you. I want to use the stack internal speaker together with the external cab.

Are all 3  fuses  in  the  Dsl 40c the same ?

Hey, new member here with a (hopfully) simple 2 part question.

First off, I recently purchased an Astoria Custom combo amp and I'd like to see about converting it for use with a standard USA power outlet. Does the Power Transformer have a 110 Volt tap or would the Power transformer need to be changed out? How extensive a change is this? Is there a Service center that can make this change for me in such a way that it will not void my warranty?

And in the second part of the question, in the interim until I can get the amp converted I've been using a power transformer to step up from 110V to 220V. What is the optimal wattage rating I should be using for this amp?

Thanks so much in advance for your help on this issue. - Joe

Hey guys, what would be the best set up for using a loop pedal with a code 50? Is it possible?

OR is there a way to start/stop recording with the looper preset via the footpedal?

Thanks in advance ;)

I have pre-ordered and am paying for the CODE 100 heqad from Sweetwater. Two questions: Are you addressing what seem to be the many issues the platform is experiencing? And is there any update on the release/ shipment date?

G'day Team,

Just wondering if there's any info I can get on a transformer for my DBS7200? It's shit a transformer and I need to get a replacement.

Cheers

JackBoy