Is there any way to update the firmware on my code 50 without a computer as i do not own one ?

i want to update my firmware on my code 50 amp

I'm assuming I have 100 slots on my CODE 50 for whatever presets I choose. How do I specify which numbered slot I wish to update or change with any of the presets on MyMarshall.com. Not sure if this question makes sense or if I even worded it correctly. 

new purchase. I have a custom Eddie Van Halen replica orginal. Excact copy of the famous Frankie. 

I have spent time on the app and making adjustments however I dont get the sound i was hope for. Perhaps I need to add an FX ex Boss ME-50. To get the sound i am looking for.  ACDC / Kiss / VH. all i get is a little louder version of my guitar. I have watched many videos on line and they change the setting and get classic rock sounds. Like a Gibson or whatever. Classic rocks sounds.  I have tried many VH and ACDC pre programmed set ups and still not he tone i am looking for. What am i missing?

Thanks 

Hello,

When I switch off the amp there is always a crackle in the loudspeaker .

Is taht normal or not ?

Thank you for the response.

Kind regards

Claude

where can I download code editor for windows ?

Is there a specific way I should be using these volume knobs ??? I like a gritty, crunchy, clean sound. Like 70's -80's bands. Bad Co, The Baby's, Foreigner

Hi,

I know that this is a recurrent demand, but please, no more "control the volume using Gateway app" answers, everybody knows that this is a component issue, not a software need for update or anything. The fact is that master volume pots are either low quality ones, or defective manufacturing components. So, all I need to know are the specs of this component (resistance values, taper, etc.) so I can purchase the correct component and replace it myself. Also, understand that I live in a place where there is no authorized Marshall servicing, and my Code amp is over three years old, therefore without any warranty. Again, please no more "send equipment to an engineer" answers, I have enough ability to do the work myself. A good thing would be if you make available the schematic diagrams of the Code amps, but I think that might be not possible. or you would have done it a long time ago.

Thank you in advance for your attention! Marshall Code RULES! But without that scratchy pot...

Best Regards,

amp powers on and presets all show up and change. sound just cut out! appears like petal display still changes buut no sound at all. jjust stopped in the middle of the song. ran a firm update and reset to factory...nothing

On the DSL 100HR, made in 2022 ... where are the fuses located? On the DSL2000 100 head 2 on the back? Just wondering? Thanks!

I have a DSL20H, a DSL40CR and now a marvelous new SC20H. I have a TC electronics Nova pedal which i use in the effects loops of the two DSL amps. When i plug it into the SC20H there is an audible hissy noise which is not there on either DSL amps. Is the effects model fundamentally different between the SC20H and the DSL amps ? Should i expect the SC20H to have a noiser effects loop ? 

Impossible de mettre a jour le fireware. J'ai fais toutes les modifications proposées par le site (chrome : vérification de mise à jour et modification pour acceptation midi) mais j'ai toujours le message "CODE : pas connecté. 

Comment faire cette mise à jour ?

I am interested in buying a MARSHALL CODE 25, but I would need to use the line output (to connect to a mixer or another amplifier), I know I can use the headphone output, but how can I use the headphone output? without disconnecting the speaker from the amp? Is there any way to achieve it?

Hello, the model is DSL40CR: thomann.de/pl/marshall_dsl40cr_cream_levant_ltd.htm
I turn on the amplifier, in STB mode the Ultra Gain LED lights up, I switch to Classic Gain and after about 3 seconds the amplifier automatically switches back to Ultra Gain. The same thing happens if I connect headphones to EmulatedOut, so I can only play on headphones on the Ultra Gain channel. However, if the footswitch connection is in STB mode, then I can play with headphones on both the Classic Gain and Ultra Gain channels. Is it normal, if there is no footswitch and I switch between Classic Gain and Ultra Gain, the amplifier automatically switches to Ultra after 3 seconds - making it impossible to play with headphones on the Classic channel. If footswitch is connected then can i play both?
Can someone check this out?

Salut tout l'monde!

Une petite question pour connaître vos expériences avec le modèle Kilburn II.

Quand l'appareil est relié via un câble stéréo en réception d'une table de mixage, la connexion Bluetooth devient instable et offre des micro-coupures de 2-3 secondes toute les cinq minutes environ, sans déconnexion de l'appareil.

L'effet se produit même quand la table est éteinte, et quelque soit l'émetteur radio.

D'autres utilisateurs ont déjà fait face à ce désagrément ?

I recently purchased a code 25 marshall amp and can't figure out which USB is the correct kind for the amp. I want to be able to connect my amp to my laptop so I can record music. 

I can't figure out how to register my new Marshall Amp on your website???

I have a DSL H and two 1936 Cabinets. What is the proper way to hook these cabinets up to my amplifier

I purchased my DSL40CR in Sept 2020. Its never left my bedroom, never been played particularly loud and (unfortunately) I have not had a lot of time to use it.  The presence and resonance originally worked when I received the amp but now turning either of these two knobs has no effect.

Also there has always been an occasional, infrequent, weak 'crackle' noise.  Is this a tube problem or is this normal for this amp?

Is there an 'easy' fix, like swapping tubes?  Is that something I can do myself?

Please let me know what my options are.

Thanks,

Dean