Has anyone used a small pedal amp to input the headphone to a amp like the electro harmonix 5MM.  I saw this done on a Spark amp to connect to a speaker cabinet.  I would think I could do the same on the CODE.  Adapt the 1/8 to 1/4 to go from headphone jack to the input on the 5MM and then in my case that speaker cable goes to a mixer.  I know this amp does have a dedicated line out to do what I want to do.  So I think this would accomplish the same thing.  Any thoughts good or bad?  I plan to try as soon as I get my hands on a small pedal(not a stomp box, just a pedal size amp) and configure the cables to go from 1/8 headphone to the 1/4 input on the amp.  I'm not an electrical engineer, I just need a "line out" if possible.  Should work.  Thanks,

Hi! On Marshall's official website, the description says that the PEDL-91010 pedal has indicator lights. Mine doesn't. I saw that in others they don't have it either. What happens? 

Hy folks!!.

I just bought a marshall code 25, and when installing the marshall gateway app on mu iphone 12 (ios 14.8.1), and open app i get the following error: "context3D  not available!  Possible reason: wrongrendermode or missing devicr suport. " and it does not work. What I can do?

Hi,

I bought a DSL20, and since I have installed 2 pedals throught the FX loop, I got an issue with the sound that drop down, becomes muffled and dull. When I switch off the fx loop, the sound becomes normal and clean.

I didn't have this issue when I had a KORG Pandora multieffects on the FX Loop instead of my 2 news pedals (TC electronic chorus and MX delay).

Could you give me any information,

Best Regards,

Frank.

I have had my Code 50 for a while and have played around with it to no avail. It's 20-50X too loud. When I set the Master Volume control to something like .5 it's way too loud. I can adjust the volume within the preset but if I change to any other preset it almost knocks my house over. I think this amp is unusable and has some serious design flaws. Is there a way to knock down the volume for the entire amp and all the presets? I need them all set at around a .1 or .2.

When I use my marshall on the pc I get really strong buzzing when recording and hearing.

I tryed 3 different cables, and updated the firmware 3 times already.

I'm out of options, this turned to be a nightmare to me.

hy

marshall gateway app is not working with android 11 version

the bluetooth connection is in place (blue light is in on) but opening the Gateway App the connection to the amp is not detected

can you please give me the info to solve the issue?

i've tried with another phone with android 10 sw version and the app is working

I think the app need some update to fix this bug (my version is 1.5.5 )

please consider that android 11 will be the standard for the most part of your code owner in the world

best regards 

Luigi

Hi,

I'm having problems with my Major IV, frequently they stop working and then I can't turn them off or on. It's not a question o battery level because they are fully charged. If I connect the cable they work normally. Is there a possibility of a reset or firmware update?

Thanks

Hi,

I recently bought a used DSL40CR, so far so good.

I play a guitar with EMG 81 setup that works normally perfectly and got no issues with another amp.

When I play in clean channel (grean), pot setting about 1/3, the amp gives to much distortion, it almost souns like clean channel red.

Guitar is in very conditions, best mechanical setup and the electronics has been checked as well.

All tubes of the amp are new and BIAS setting adjusted to 35mV.

I don't know what else to check, could it be a grounding issue?

The amp has a very low noise what I assume is absolutely normal.

I can't play clean with this seup.

Anyone an idea what can cause this issue?

Regards

Joerg

How do I have chorus & flanger at the same time 

Does the Marshall Code 100 take pedal well? 

I'm considering buying a wah pedal but I'm not sure if it will work well with the amp. 

I bought a midi controler, but i dont have de marshall code to program the midi control

My serial number is 73400553H04769I0806970

i bought a Marshall emberton Bluetooth speaker .How can I validate of my speakers are authentic or fake ?

Hello Team,

I do have a couple of questions. 

1. I have a DSL20CR and would like to upgrade the speaker to 8ohm. So if ever I install an 8ohm speaker and plug in the 1x8ohm at the back panel, would it be fine? I mean no issues that will be experienced in the transformer?

2. Furthermore, just recently bought a marshall DSL1hr (last weekend) and very happy with it. I just saw there is a cable included saying:  "Marshall PVC 0.85 sq mm x 2 cores wonderful vn (lf)"

Is this a speaker cable? I'm not comfortable using it before I confirm.

Thanks a lot.

Mike Burny

Hi there, just purchaced a Code 50, installed the Gateway app for iPad. All working a treat, eccept that if I am connected to the Amp via bluetooth, I am getting all the keypad sounds through the amp, also incoming messages, email notifications and phone calls. is there a way of stopping this????

here are the seriel number of marshall emberton 73400553E13591G0253233. Can help me check weather is fake or real ?

Had Code 50 for a few days and the LCD display is now not lighting up orange,

it still works the same but no light and quite difficult to see in dim light.

Any Ideas ?

When I select the tuner the display only shows.  C : > | . I think the firmware is M1.1.

Any ideas? Thanks

Is there a direct connection from the Code 100 amp to a Scarlett audio interface?