Can you factory rest all the Code 50 pre-sets, and if so, how?

This really stinks...

I have a brand new Code 25 and it stops playing through the speaker after a few seconds.  The output is always there when I plug in a headset, but the speaker plays for a few seconds then goes quiet.  I redownloaded and installed the firmware.  I tried different settings and different presets.  Nothing works.  Any other advice before i talke it back to the Guitar Center?

Hello, there. First of all sorry for my bad english.

I got two CODE 25, and it cannot be automatically paired with my phone again if it was rebooted.

When it is turned on, the blue light does just keep off and never get reconnection process.

Both of these got this issue after firmware update, and factory reset and troble shooting guide does not help anything.

I tried every ways so many times but it was useless.

There are many users suffering from this issue just like me... it is really annoying even this amp is really good.

Please leave an advice. thank you.

There are many questions & answers referring to an imminent update to the code firmware. I'm guessing the firmware is largely the same for both except there are some differences so are we talking about updates to both 25 & 50 or are they staggered?.

Since the update has been "soon" for some time I can only assume that the testing and acceptance etc is taking longer than expected. Are you able to state what is being slated in this update?.

Thanks for any information you can offer

Hi guys,

This isn't really a question but a solution to your problems connecting the Code to Studio One for USB recording. I got it to work using ASIO4All.

Here is a quick 2 minute video I made showing how: https://www.youtube.com/watch?v=LC1FAeFyRn8&feature=youtu.be

Marshall, feel free to point people here if they need this solution. Presonus just points them back to you.

David

Hi, I need a little help,  I'm a newbie on this...

I know my code 50 doesn't have a "line out" but it features a headphone out, can I conncet the amp to a Yamaha mixer? I want to control my guitar volume with the mixer, plus a mic and an acoustic guitar.

If that is possible, how should I set the master volume, the preset volume and the gain in my marshall?

thnak you!

It's now mid October and still no Mac support.  Can we expect Mac support before the end of the year?

Hello:

I just purchased a Marshall JCM 800 Head and a 1960a cabinet for my office (small space not the best for this set up), but I am very new to marshall amps and heads.

would anyone know which settings on the back of the head to set to?  it is a small space and dont want to mow any down with the volume.  Everytime I switch it off I head a very loud electric 'switch' sound, sort of scary and worries me (dont want to damage the eqipment).  

Any suggestions from anyone.

Thanks so much in advance...

Mark

I dont know why you removed the feature of turning off the standby mode. It was a terrible decision. We need smart devices and not dumb ones. You really expect me to press a button on the speaker every time I use it after 20 minutes? Please update the app and firmware so we can enable turning off this stupid feature.

When will there be a firmwear upgrade to correct the bluetooth connection problems ? I have followed all the instructions on the forum and still only occasionaly manage to get a connection before it disconnects or freezes at rehearsals which is very frustrating to say the least.

Using an Iphone 6s and the latest firmwear version with Code 25

Come on Marshall this is becoming a big issue 

Hi there,

I have a problem with the Stanmore II Speaker.
It is connected via Cable to Amazons Alexa. When music is played, it always is ínterrupted by the starting/pairing sound (that e-guitar chords)
as if some device is trying to connect with the speaker. we turned every device nearby off (which shouldn't be the idea, right?) but it still
continues. it's quite annoying.

any ideas?

Hello, I know this has been covered here and I have read all of the messages, but I would like some newer feedback regarding my newly purchased DSL40C implimented with a Line 6 POD 2.0.

I realize you can't shut off amp modeling and that to achieve the least amount of colorization, and preserve my Marshall tone as much as possible, I should set the POD 2.0 to Tube Preamp, and EQs to 12 o-clock, which shuts off Cabinet Simulation.   I want to use the POD 2.0 because it has a bunch of presets I use, which I will modify and it gives me multi effects with a Pedal. 

How should I route this, given the effects send on the DSL40C is probably line level, and has no attenuator. The POD 2.0 has instrument in and I presume Instrument out. I know it will run -10 and +4 when using TRS. I will say I don't see any documentation on the DSL40C loop. 

This is my first Marshall setup and need advice from you gurus.

Any and all advice is appreciated.

Thanks so much!

Hi, Is there a way to reduce the power on a Code 25 from 35w down to 5w or 1w like you get on modelling amps from 'other' manufacturers?

To use as a practice amp in my home, I'm having to set the master volume and volume controls really low on the amp and still dial it back on the guitar to the point it is affecting the tone of the preset.

Since this was not obviously available on the top panel, I wondered if it was available via the app but I can't find it if it is.

Thanks in advance.

Hi

I’ve used my Code 50 for the first time since updating my iPhone to iOS 11 today, and the Bluetooth connection is dropping every few seconds. I have to close the app, turn Bluetooth off and on and reopen the app. Then it drops again. I never had this problem before updating my iOS.

Has anyone else seen this? 

another question, are you guys going to make a cover for the code amps? just something that will protect it getting to and from rehearsal?

also, is there a setting on the for forum  i can set to be alerted to an answer via email?

thanks

i can play backing track thru amp but no sound when playing guitar

will mg series foot controller work with code series amps.the guy at guitar center ordered me mg4 item 476224000000000 instead of code series 1500000005811 for my marshall code 50 yesterday.I stopped by today and he thinks itll work,but i think maybe features are different and also think quality of code stompware may be better,any advise?It's a pain cause i have to wait until end of week to get mg4 and then return to order correct pedal,THANKS

Hello everybody.

I just have one quick and easy question: can I sweep a couple of KT66 power tube instead of its original 5881 in my JTM45 2255 reissue head?

any risk or anything to set?

thank you all in  advance 

kind regards

Claudio "Klide" Bauducco

Several times now, the Code 25 has locked up on me when trying to use it from the Gateway App on my iPad.  Symptoms are that the display will freeze up (text no longer scrolls) and the different buttons (including gain, tone knobs, etc) will become completely unresponsive.  Controlling it from the iPad will no longer work either.  The only thing I can do at that point is switch the amp off & on again.

Additionally, trying to connect the app to the amp is really hit and miss (yes, it's paired successfully):  sometimes it refuses to work, sometimes it will freeze the amp and sometimes it will work, but switching from ipad to amp presets will not. 

While waiting patiently to see if / when the CODE100 amps. are going to be available I happened to look at the supposed specs. for the CODE100 on your (Marshall) website found here: https://marshallamps.com/products/amplifiers/code/code-100h/

I couldn't help but notice that the CODE100 will allow 5 x simultaneous FX to be used.  As we are all aware: this is not the case with the CODE50 and CODE25 i.e. only 1 x FX may be used.  Aside from the obvious physical difference and output between the CODE100 and the CODE50 and CODE25: everything else appears to be the same other than the number of simultaneous FX that may be used.  So my question is: is it not just a simple firmware update / upgrade that will allow for 5 x simultaneous FX to be used with the CODE50 and CODE25???  If so: could we have it please (or could we at least have some input or further information on this)???  In hindsight and as wonderful as I think these amps. are: it's starting to not make sense to me that I still have to purchase stompboxes if I want to use, for example, a compressor, additional distortion, and, say, an octave (pitch shifter) when all of these FX are actually included on the CODE50 and CODE25 but only 1 x FX can be used at any given time.

Regards,

Dale.