Hey guys, I want to buy a really good Bluetooth speaker, and I was looking at the Marshall's Stockwell and Killburn models (the first models, the new ones are too expensive lol). Are they worth it? I've read that sound quality is amazing but at the same time, they're 2× the price of all the other portable speakers. Thanks in advance 👍 PS: I also really like the design, but that's not enough to pay double the price.
I left the F/S aside for a few days and today when i decided to use it just stoped responding.
The display shows A1 sometimes it twinkles, sometimes dont. But It doenst responds when i press the buttons.
I press ALL the F/S buttons and nothing happens!!!
I didnt drop it or nothing similar, the F/S is kinda new i bought it in June, the F/S conditions is visually intact.
Am i forgetting something?
Things that i've tried already:
- Factory reset my Code 50
- Factory reset my F/S
My setup:
Foorswitch 91109
Marshall CODE 50
I'm attempting to discover a channel exchanging pedal for my DSL 100h. The Marshall site says it utilizes the PEDL-90012 which is out of creation. Can I simply utilize something like the MRPEDL91003 or do I have to get the first footswitch? tellthebell
Hey guys , I just bought a Marshall avt 100 valvstate 2000 . where can i download the manual ?
thanks
I've had my Code25 for about 4 months and it worked fine the first 3. Then about a month ago, the preset readout faded to being almost unreadable. Then today, it stopped working completely. I can't use it for my guitar or as a Bluetooth player. Not sure what to do next?
Hi guys i have a Code 50 Amp and footswitch. i have recently started to having a problem. when i am on a patch and hold in the Selector on the Switch for instance if i am in Bank B3 and hold down the B3 switch, you enter a mode which you switch off FX, Delay and reverb. i have notiched that when i go into any bank like that and want to go back out to choose another patch my amp buttons and knobs & footswitch is non responsive and i have to switch the amp on and off for it to respond again, this is very anyoing. any feedback on what the problem might be
Hi.
Is it just me or have these forums become extremely slow and unresponsive since the weekend??? I also cannot login from my iPad for some reason i.e. I get an error on the iPad (I think it's timing out). And from my PC's the forums take an age to load. They're now operating at the same tilt as support!!! LOL!!! (Sorry: just having a bit of fun!!!).
Regards,
Dale.
Where can I find a schematic for a DSL 40C? I have an open short somewhere in the power circuit.
Just wondering, to create a sound like the Cure i'll be needing probably chorus and phaser and/or flanger. Can these be done on the Code50 at the same time or do I buy a multi effect board?
Hello,
Can you run a JVM Combo amp in to a reactive load box and then in to a Audio Interface connteted to a DAW? Would you be in standby when doing so or standby off?
Here's the solution to pairing an iphone/ipad to CODE as of latest apple update. Stop blaming Marshall and learn to work your Apple device!!! Too many whiners complaining about problems that have everything to do with dumb Appple users!
1. settings>gateway app (find in list of apps)>turn on Bluetooth & other options you prefer
2. settings>bluetooth (make sure bluetooth is on), then pair CODE with device following the regular pairing instructions
3. APOLOGIZE to every person you bitched to and learn to work your amp and phone like a capable musician and not the babboon that you are!
Hello.I have a big problem with my amp.When I increase the volume level,from my cabinet sometimes come out very loud and terrible sound.It is just like the amp will blow my cabinet 2x12 120W.Ultra gain section - Volume at 5 and more,Gain at 5).Is this bad tube,or something problem with amp?Sorry for my english!
hello when i change patches on my code 50 , despite using the same pre amp and power amp im getting a delay on the patch change, approx 2 seconds untill the selected patch actually kicks in. is this down to the DSP chip recalling the set ups? also has anyone tried playing this code with cab sim off. sounds quite good like my old TSL combo. not bad at all .
I have had my DSL40 for about 5 years now. Today I turned it on and have zero gain. The volume seems to work but no distortion, even on ultra gain. I am assuming this means the tubes need to be replaced, but the poerp or preamp tubes? Or all of them?
hi everyone, does anyone have a preset for a code 50 for Leslie West. if anyone here is old enough to remember who that is?
think MOUNTAIN or MISSISSIPPI QUEEN.
also, is there a way any answers i may get show up in my email, or do i have to keep checking back on the forum?
thanks so much
jp
Hello,
I purchased the Code 50 because I have alwasy wanted a marshall and im absoultly loving it. My question is, I know there is an ability to record with it. Now im clueless on who abouts to do it. Any idea on where to start or programs and such?
Is there any alternative to the Marshall Bluetooth App for the Acton / Stanmore II / Woburn Series?
Specifically is there another way to link up two speakers to a stereo pair? Maybe a desktop client or maybe even a command line tool?
Or is anyone aware of an e.g. an open source project that reverse engineered the protocol? I can't be the only one out there finding the app horribly unintuitive and poorly programmed, also some functions simply do not work - e.g. source selection for a coupled pair.
Thx...
Hello, I've had my code 50 for about a year and a half. A few months ago I noticed my amp would stop projecting any noise a few seconds after i would turn on the amp, i found it weird because when i play with my headphones plugged in it works fine but when the signal passes through the speaker it stops making any noise, just completely shuts off.
It isnt the cables or the guitar as I've tried multiple on the same amp, so I imagine it is a problem with the speaker, anything I can do?
Looking for the best way to run a 1922 ext cab rated for 8ohms and use together with the internal 16ohm speaker. Can the speaker outputs be mixed? i.e. 16ohm speaker to the 8ohm output and 8ohm cabinet to the 4ohm ouput to achieve 5.33 load?
Hi, Marshall team!
Is it possible to add graphic or parametric (or both) EQ in the future firmware update?