Questions
Showing results 161 to 180 of 3374
0

votes

0

answers

167

views

Hiii

Last month (Sept. 2021) I was able to sync my Amp with the Gateway app. Unfortunately, This month/Today the app cannot detect/connect to my amp.  I already updated the firmware of my Code 50. Is there a way to sync it? because I already did what the tutorials said.

 

Thank you.

asked 30 Oct 2021 at 07:27 AM

Gabriel Sumat
0

votes

2

answers

229

views

Is V3 the output valve (ECC82/12AU7) on this amp? I have found no information elsewhere on Marshall's site. Thanks in advance. 

asked 30 Oct 2021 at 01:44 AM

Colin Tams
0

votes

1

answer

213

views

What does this new software 1.46 do????

Does it effect any amps....???

Like make the OD JVM MORE realistic???

Or something like that...???

asked 29 Oct 2021 at 08:05 PM

Allen Perez
0

votes

0

answers

180

views

Hi,

I understand the D.I. output is balanced with the signal at mic level. My questions are about the tech specs of the Line Out jack.

Is the Line Out balanced or unbalanced? -10dB or +4 dB?

Assuming it is unbalanced, if I want to feed that signal into a balanced line input on a mixing board (a) using a 20 ft cable or (b) using a 100 ft cable, will it work with no adverse effect on signal or sound quality?

Thanks for your help,

 

asked 29 Oct 2021 at 07:18 PM

George Mack
0

votes

0

answers

234

views

Hi There,

For lowish volume practice I can currently run the SC20H on 20W mode with the  master at about a 1, or just slightly above that on 5W mode (maybe just under 2) with the preamp at around 8 in both cases. Is there any benefit to getting an attenuator to be able to run the master at higher volumes?

While I am asking: Does the poweramp distortion of the amp behave differently in the 5W mode vs the 20W mode? I.e., in 5W mode does the power amp distort at lower numbers on the master volume than in 20W mode? For both modes, what is a good number at which above power amp section distortion is occuring (not factoring in specifics like pickups, etc)? 

 

Thanks!

edited 29 Oct 2021 at 03:39 PM

John Markos

asked 29 Oct 2021 at 02:01 PM

John Markos
0

votes

1

answer

192

views

Will a splitter be able to connect the sound from both laptop and speaker and be able to use the bass,treble,volume controls on the speaker? 

asked 29 Oct 2021 at 01:51 AM

Yoseph Dagim
0

votes

1

answer

213

views

Hi!

I bought a Marshall CODE 100w in Feb/21. It wasn't even used 10 times.

Yesterday when I went to turn on the equipment, the amplifier started to make a noise. I thought it might be the cable, but it wasn't.
Even without the cable connected to the equipment, the noise continued.

I reinstalled firmware but it didn't work either.

I do not know what to do.

Could you please help?

asked 28 Oct 2021 at 05:22 PM

Linneu Silva (1)
0

votes

1

answer

161

views

Hi all

Very often when I press the down channel button on the pedal, the amp goes UP and channel!

Its a pain in the but, makes it impossible to play with,  tell me there is a fix for this?

Thanks all!

asked 28 Oct 2021 at 12:51 PM

Matt Sykes (2)
0

votes

1

answer

134

views

Hi 

 

I have recently purchased headrush gigaboard multi effect and when I use the 4 loop fx pedal on Marshall Origin50 amp, the amp volume reduces by 95% . It works well with Fxloop light off but that means the fxloop is not working. What could be the issue

asked 28 Oct 2021 at 02:19 AM

Alok Magan
0

votes

0

answers

202

views

Hello guys,

I'm in sort of a pickle as I can't seem any info about this.

I have a Stanmore II that is absolutely perfect. I however long for that stereo effect :)

Hence I'm planning on getting a 2nd one, but I primarily use my PC and laptop for listening to music. I was wondering would it be possible to pair the two via the app on my phone and then connect them to the PC/laptop.

My logic here is that if I tingle the bass or treble via the phone app, it seems to "stick" with the speaker and then if I connect it to the other device, the settings stay the same.

So it's only logical that if I pair the two via the phone app, when I search via my laptop I'll find 1 coupled device to connect.

Anyone done this setup?

asked 27 Oct 2021 at 05:46 PM

Ivan Georgiev
0

votes

0

answers

143

views

I have the original Marshall Stanmore. It's wired direcly to both a turn table and a CD Player. The sound recently began cutting out intermittenly. I hear a bit of static, the audio cuts out, and then a few seconds later, the sound comes back. I've been using the same setup for about a year with no issues. 

Any ideas?

asked 26 Oct 2021 at 11:45 AM

Fred Quattrone
0

votes

6

answers

296

views

Hi everybody

My CODE 25 was working like a charm. After the firmware update there is a horrible whistling high frequency noise coming out from it. It is really bad. 

Anybody can help me out with this? How to roll back the firmare?

(It's not the guitar/cable/ground because I have another amp and I did a test)

Thanks

Matteo 

asked 26 Oct 2021 at 09:29 AM

Matteo Bassi
0

votes

2

answers

229

views

Hi,

I have a CODE50 (1 week).

After editting a preset, I click and hold the exit/store button to save the changes I made. The changes are stored but the CODE then "freeze".. no sound, no change possible. After switch off/on, everything is back to normal. The preset is updated.

Same thing is happening when I store the preset in the footcontroller.

Is that "normal"? Am I doing something wrong? I presume that I'm not supposed to do a switch on/off everytime that I want to store a present change...

Thanks in advance. ? ? ?

edited 12 Nov 2021 at 10:25 PM

Bernard Huber

asked 23 Oct 2021 at 02:33 PM

Bernard Huber
0

votes

0

answers

140

views

Buenas, tengo la cabina Marshall code 100 y una interface scarlett 2i2. Me preguntaba si es posible conectar el marshall a la interface a través del fx loop o si por el contrario solo es recomendable hacerlo de otro modo. Mi intención es grabar el sonido del Code a través de la interface. He visto algún video donde conectan el multiefectos por ejemplo un Kemper a la interface a través del send del fx loop a la entrada de la interface pero desconozco si la Code también se puede conectar así al ser digital. Gracias de antemano. 

asked 23 Oct 2021 at 08:23 AM

Adrian Rodríguez
0

votes

1

answer

206

views

Hello. I recently bout the CODE 50 and it's great, but the gateway is pretty much useless for me. I have tried pretty much everything and it still will not connect to my iPhone 11 pro max. I have had friends try the app and it works fine on their phone, but when it comes to mine, nothing! Really love the amp and would like the bluetooth to work from my phone so i can adjust with ease. Not the end of the world, but it is advertised that you can control everything from your phone so that's what i would like to do. Any solutions? Thanks.

asked 20 Oct 2021 at 11:15 PM

Gabriel Loza
0

votes

0

answers

168

views

What is the best way to turn it off no standby switch?

asked 18 Oct 2021 at 10:16 PM

Eugene Canney
0

votes

0

answers

192

views

Hello,

If I need to replace the stock preamp tubes in the Origin 20 H, what is the exact model.

It show ECC83H and I think they are Shuguangs but not sure. They used to be Marshall branded Shuguangs or JJ but these have nothing written on it except ECC83H. Looks chinese but they sound best I think to nail that JCM-Plexi tone of the Origin. I tried other and it is a slightly different sound. I need to know the exact model.

 

Thanks

asked 18 Oct 2021 at 01:50 PM

Pierre Robinson
0

votes

3

answers

178

views

After a windows update to windows 11 I got this error:  Font 'Cooper Black' cannot be found. That makes the app crash during the start. Trusting the fix will take a while I installed the font myself I got from the website Cooper Black Font: ? Then the CodeEditor worked normally.

I'd like to ask Marshall's devs to solve this one. Also, I'd like to help other people with the same problem.

That's my contribution to this community.

asked 17 Oct 2021 at 07:54 PM

Geraldo Andrade
0

votes

1

answer

180

views

Hallo.I just bought a brand new Marshall Origin 50 h and the power scalling is not working.5-10 or 50 watts sounds the same.No sound or volume difference.

How can i solve the problem.I think the amp is locked on 5 watts or 10 cause my other 15 watt amps are sounding louder

asked 16 Oct 2021 at 07:08 AM

Bill Markos
0

votes

1

answer

172

views

Hello there!!

 

I recently bought a used Code 50. It needs to be reset I believe. I can't get the tuner turn on. I can't adjust any settings.  It plays, but sounds a little muddy at times. Would really like to be able to adjust the different mods and amps and what not. Thank you. 

asked 14 Oct 2021 at 02:33 AM

Tyler Hughes
Showing results 161 to 180 of 3374
Loading - please wait...