Have any of you CODE amp owners found a good Robin Trower preset? Thanks.

Hi,

I recently purchased a Code 50 and have been trying to connect it to the gateway app on my Android phone. The phone connects to the amp successfully via bluetooth and I can stream the audio out to the amp directly using Spotify but when I go into the gateway app, it says "Not Connected". I tried the "Scan for Amps" button but it doesn't find anything. Any help is appreciated.

I researched 1x12 open back vs. closed back vs. ported cabinet guitar cabs. My experiment with my Code 50 amp was to remove the back without unplugging anything so I could here the difference between closed back and completely open back. The amp really came alive with a lot of punch and presence while ridding the boominess that occurs. I removed the power cord socket and cut a square the same size as the speaker. This was an improvement but I liked the complete open back sound better. I then cut the back out more leaving just enough stock to support the existing power cord socket hole and protect the electronics inside the cabinet. I will continue with cosmetics such as painting inside black and/or add a grate for protection. To my ears the amp really came to life open back. I will keep it this way. It is an easy experiment to try without sacrificing anything, just remove the back cover screws and pull the back away. If you hate it you just refasten it and leave it original.

.

Hi.

Just a warning (possibly more a bit of advice maybe):

I noticed over the weekend that sometimes (not always) when retrieving a patch from a CODE amp. the Marshall CODE PC Editor does not always get it right.  Sometimes it will load perfectly and other times it's almost as if it's retrieved some, not all, of the settings for the patch.  I only noticed this after retrieiving some presets, making a change or two, and then overwriting on the amp. with the incorrect settings and I thought I was going bonkers because I checked and re-checked what I was doing but whenever I saved on the amp. sometimes one or two of the parameters were not as I set them.  It seems to do the same when loading a saved patch from disk too.  Wasted hours!!!

Anyway: the easy workaround really is to just keep clicking on the retrieve button until there are no more changes to any of the parameters of the preset being shown on the screen (normally only need to do it twice but three is a lucky number).  Make your changes then save back to the amp. (I've resorted to doing this three times too just for safety sake).  And when loading from disk: get into the habit of doing it three times too!!!

I'll try get their support to have a look at it (although things seem every so quiet over there).

I mention the above because even although we all know the this is not a Marshall Amplication PLC product and is not supported by them: it is indeed punted on these forums quite widely (by myself too).

Regards,

Dale.

This is not a question but a response to those who have asked if there is a way to reduce the output wattage on Code amps to make them quieter. The short answer is no, not out of the box.

However, the speaker(s) that come with Code amps are 4 ohm. In the case of the Code 25, you can swap it out for a Celestion G10N-40 10" 8 ohm speaker (about $70 on Amazon) and reduce the output from 25 watts to 12.5 watts due to the change from 4 ohms to 8 ohms. Instead of running the master volume at < 1 when I'm jamming with my stereo, I can now run it at about 3. The added bonus is better sound - you hear the distortion from the amp itself with less mud and distortion from the speaker. This will not harm the amp in any way as driving an 8 ohm load requires less of an amp than a 4 ohm load.

Full disclosure, this was not my idea. I read about this from another Code 25 owner. Enjoy!

I am wondering if anyone has a preset that will work for using an external effects pedal into my Code 50? I only want to run the external effects (distortion, reverb, delay) and nothing fromthe amp itself. What I am seeing is that even with all effects (amps, modeling, etc.) turned off on the Code my pedal into it sounds like garbage. Very muffled, bassy, and muddy. I have the EQ on the amp set so that the bass is all the way down and mid/tebble are all the way up and it still sounds terrible. I don't want to have to edit and mess with every patch on my old Zoom GFX8. The pedal doesn't sound like this into my old 40 Watt Fender bassman.

Any advice on setting up the Code to sound good with external effects would be greatly appreciated.

link...https://www.ultimate-guitar.com/forum/showthread.php?t=294480&per_page=40&page=1

not my work at all, i jut found it and thought it may assist some of you

John Petrucci of Dream Theater
1)Clean Channel:
Preamp Mode: Rhythm 1 Yellow
Gain: 6
Treble: 6.5
Middle: 3.5
Bass: 3
Lead 1 Drive: 0
Lead 2 Drive: 0
Master: 5.5
Presence: 8
Dynamic Voice: 7
Power Amps set on Deep And Modern

2)Main Distortion Channel:
Preamp Mode: Lead 1 Red
Gain: 6
Treble: 6
Middle: 6
Bass: 4.5
Lead 1 Drive: 4.5
Lead 2 Drive: 0
Master: 4
Presence: 6.5
Dynamic Voice: 6.5
Power Amps set on Deep And Modern

3)Lead Channel:
Preamp Mode: Lead 2 Yellow (MarkII Lead Sound)
Gain: 7.5
Treble: 4.5
Middle: 4
Bass: 5.5
Lead 1 Drive: 0
Lead 2 Drive: 6.5 Master: 6
Presence: 0
Dynamic Voice: 3

4)EFFECTS CHAIN:
Clean Sound - basic chorus sound
Lead Sound - 602 and 460 millisecond delay with 3 repeats
Crunch - 26 milliseconds delay

Jeff Loomis of Nevermore
Pre Gain- 6-9
Low- 4-7
Mid- 5-7.
High- 5-7
Post Gain- 7-10.
Presence- 5-7

Tom Morello of Audioslave/Rage Against the Machine
Gain - 7
Treble - 10
Mid - 4
Bass - 4
Reverb - 0

Eric Clapton of Eric Clapton
Gain - 7
Teble - 5
Mid - 7
Bass - 7
Presence - 8

Mick Thompson of Slipknot
Gain - 9-10
Treble - 8
Mid - 7
Bass - 8
Reverb - 2
Note tuning of B F B E Gsharp Csharp (low to high)

Jimmy Page of Led Zeppelin
Gain - 4
Treble - 8
Mid - 3
Bass - 7
Reverb - 2

Kurt Cobain of Nirvana
Gain - 7
Treble - 7
Mid - 4
Bass - 3
Reverb - 2

Eddie Van Halen of Van Halen
Gain - 6
Treble - 4
Mid - 3
Bass- 9
Reverb - 4

John Frusciante of Red Hot Chili Peppers
Gain - 4
Treble - 8
Mid - 2
Bass - 6
Reverb - 7

Kirk Hammet of Metallica
Gain - 7
Treble - 7
Mid - 2
Bass - 7
Reverb - 2

Keith Richards of Rolling Stones
Gain - 4.5
Treble - 4.5
Mid - 6.5
Bass - 5.5
Reverb - 1.5
Note use of open G tuning, D G D G B D (low to high)

The Edge of U2
Gain - 1.5
Treble - 7
Mid - 5
Bass - 3
Reverb - 8.5

Brian May of Queen
Gain - 8.5
Treble - 4
Mid - 9
Bass - 5.5
Reverb - 4
Note Brian famously uses old sixpences to pick the strings of his guitar.

Jack White of The White Stripes
Gain - 8
Treble - 7
Mid - 5
Bass - 8
Prescence - 8

Slash of Guns N' Roses
Gain - 6.5
Treble - 4.5
Mid - 7
Bass - 7
Presence ? 8

Justin Hawkins of The Darkness
bass- 6
treble-8
mid-8
gain-7
reverb-5

Dimebag Darrel of Pantera
Gain - 7
Treble - 10
Mid - 4
Bass - 9
Reverb ? 0

Billie Joe Armstrong (newer) of Green Day
Drive - 6
Treble - 10
Mid - 8
Bass - 5
Reverb ? 3

Billie Joe Armstrong (older) of Green Day
Gain:9
Treble:10
Mid:8
Bass:5
Reverb:3

Dave Murray of Iron Maiden
Drive - 7
Treble - 9
Mid - 7
Bass - 4
Reverb - 0
Use your brigde humbucker - I find this tone to be excellent for Maiden - The Trooper, Hallowed especially


Gary Moore of Thin Lizzy
Bass 7
Treble 7
Mids 8-10
Gain 5-7 depends on song
Coutour at 3-4 not so high to suck the mids but not os low to sound crappy
maybe a splash of reverb
Neck pickup

Dave Grohl of Foo Fighters
Distortion:8
Treble:7
Middle:5
Bass:3
Reverb:3 (room)

Joe Walsh of Eagles
Treble: 7
Bass:3
Mid: 4
Master:3
Reverb:2
Presence:3

Angus Young of AC/DC
Gain - 5
Treble - 10
Mid - 10
Bass - 5

Gary Rossington of Lynyrd Skynyrd
Treble - 5
Mid - 10
Bass - 5
Gain - 2-3

Mark Tremonti of Creed/Alter Bridge
Gain:10
Treb.:6
Mid.:3 or 4
Bass:7
Presence:6

Mike McCready of Pearl Jam
Treble: 7
Mid: 7
Low: 5

Daron Malakian of System of a Down
Amp Used: Crate VFX5212
Gain: 8
Treble: 6-7
Mids: 3-5
Bass: 10
Presence: 8
Note the use of Drop D down 1/2 step (Db Ab Db Gb Bb Eb)

Tony Iommi of Black Sabbath
Gain - 7 or 8
Bass - 6
Middle - 6
Treble - 6
Channel - Overdrive

Mick Mars of Motley Crue
Gain - 3
Bass - 2-3
Contour - 2-3
Treble - 10
Channel - Overdrive

Steve Jones of Sex Pistols
Gain- 7
Volume- 10
Treble- 8.5
Middle- 6
Bass- 4

Alex Laiho of Children of Bodom
Treble: 9
Mid: 4
Bass: 7
Gain: 8
Reverb: 4
(on guitar)
Tone: 10
Pickup: Bridge

David Gilmour of Pink Floyd
Bass: 10
Middle: 6.5
Treble: 10
Gain: 1.5
or
Gain-2-3
Treble- 7-8
Mids- 9-10
Bass- 5-6
Reverb- 60-70%

Carlos Santana of Carlos Santana
gain 7
treble 10
mid 6
bass 5
reverb 2

Jerry Cantrell of Alice in Chains
Gain 6-7
Treble 6-7
Mids 5-6
Bass 5-6
Reverb 3

Joe Perry of Aerosmith
Gain: 5.5
Treble: 2
Mid: 7
Bass: 2
Volume: Full (used Fenders in the early days and switched to music Man during the Toys era, now uses a mixture)

Pete Willis of Def Leppard
Gain- 4
Bass-4
Mid- 5
Treble-7
Reverb-4

Billy Gibbons of ZZ Top
Treble: 3
Middle: 10
Bass: 10
Prescense: 10
Gain: about 5 (crunchy type of sound)
Use a Les Paul guitar with not to much output in the pups and select both!

Buckethead of Buckethead
Bass: 5-6
Mids: 5-7
Treble: 7-8
Presence: 6

Boost clean channel with an OD
Tone: 5-6
Volume: 5-8 (have it boost the volume of the amp a little)
Distortion: 0

Randy Rhoads of Ozzy Osbourne
Gain 7
Bass 7
Mids 7
Treble 10
Reverb 0

Stevie Ray Vaughan of Stevie Ray Vaughan
Low 10 (full)
Mid 7.5
High 5

Steve Vai
Clean:
Treble: 8
Mid: 5
Bass: 4

Lead:
Presence: 6
Treble: 6
Mid: 7
Bass: 7
Gain: 8

Kerry King of Slayer
Gain - 9-10
Treble - 10
Mid - 4
Bass - 6-7
Reverb – 3

Opeth
Amp EQ settings:
Mids: 4:30 o' clock
High:10:30 o'clock
Low: 7 (barely above 0)
Presence: 0
Resonance: 8(barely above 0)

Drapery Falls Intro Tone(for Boss GT-6):
Only things that are on are:
-Reverb(set to 75)
-Overdrive/Distortion(Metal>Heavy Metal Preset)
-Overdrive/Distortion Drive and Level set to 100
-Equalizer:
Low EQ +1 dB
Lo-Mid f 500Hz
Lo-Mid Q 2
Lo-Mid EQ +2 dB
Hi-Mid f 4.00 kHz
Hi-Mid Q 2
Hi-Mid EQ +2 dB
High EQ +2 dB
Level +2 dB
-Pedal Assign: Exp Pedal ON, Foot vol min 0
Opeth Distortion:
Only things switched on are:
-Overdrive/Distortion TYPE: Metal>Heavy Metal(type variation)
-Overdrive/Distortion Drive and Level: 100
-Reverb: 25
-Pedal Assign: Exp Pedal ON, Foot vol min 0
-MAKE SURE YOU USE RHYTHM PICKUP FOR THIS DISTORTION

Graham Coxon of Blur
Gain 7
Treble 7
Mid 6
Bass 5
Reverb 0

Rush
Gain - 6
Bass - 8
Mid - 6
Treble – 4

Neil Young
Bass: 5
Middle: 10
Treble: 10
Presence: 10
Gain: 5

Jimi Hendrix of Jimi Hendrix Experience
Gain - 4
Treble - 5
Mid - 5
Bass - 8
Reverb - 5

Joe Satriani
1.) Gain 7
Treble 6
Mid 10
Bass 6
Reverb 1

2.) gain: 7
Treble: 6
Middle: 3
Bass: 6
Reverb: 0 (Distortion)

3.) Gain: 6
Treble: 7
Bass: 9
Mids:0

Wolfmother
Gain: 7
Bass: 6
Mid: 6
Treble: 4
Reverb: 2

Dave Mustaine of Megadeth
Gain 10
Bass 4
Contour 10
Treble 10

Matt Heafy of Trivium
Treble- 8.5
Mid-6.5
Bass-6
Gain-7.5
Reverb-none

Daron Malakian of System Of A Down (newer)
Pre-Amp: 7
Gain: 5
Trebble: 8
Mid:9
Bass: 7.5
Presence: 9

Killswitch Engage
Reverb:4
Bass:6
Mid:6
Treble:4 or 7 depending on song.
Gain:8

Random Speed/Power metal settings:
Gain: 4
Bass: 4
Mid: 8
Treble: 4
Reverb: 3

Gain: 7
Bass: 8
Mid: 3
Treble: 7
Reverb: 3

Hank Marvin of The Shadows
Gain - 2
Treble - 6
Mid - 9
Bass - 9
Reverb - 10

Pete Townshend of The Who
Gain: 5
Treble: 10
Middle: 10
Bass: 10
Reverb: 3

Cradle Of Filth
Gain: 10
Bass: 10
Mids: 1
Treble: 10
Volume: 10

Boston settings
Gain - 5
Treble - 5
Mid - 10
Bass - 3
Reverb - 0

Rammstein
Bass: 9-10
Mids: 4-5
Treble: 9-10
Gain: 10

Phish- Chalkdust torture
Gain:6
Bass:8
Mid:7
treble:4
reverb:3

Dez Cadena of The Misfits
Gain: 9
Bass: 9.5
Mid: 6
Treble: 5
Post gain: 5

Zakk Wylde of Black Label Society
Preamp: 10
Volume: 4-6
Bass: 10
Middle: 4-6
Treble: 4-6
Presence: 2

John Squire of The Stone Roses
Gain 7
Bass 7
Mids 7
Treble 3
Reverb 5

Andy Summers of The Police
Gain 5
Bass 7
Mids 5
Treble 5
Reverb 5

Paul Weller
Gain 7
Bass 10
Mids 10
Treble 10
Reverb 3

Strapping Young Lad
Gain 7
Bass 8
Mids 6
Treble 7
Reverb 0

Darkest Hour
Gain-6
Bass-7-8
Middle-7
Treble-5
Presence-7

Allan Holdswoth
Gain: 2 o'clock
Treble: 2 o'clock
Middle: 2 o'clock
Bass: 0
Presence: 10 o'clock

Brendon Small of Dethklok
Gain- 8-9
Treb-5-6
Mid-6
Bass-8

Jeff Beck
Gain - 10
Bass - 6
Mid - 5
Treble - 7
Reverb - 4

Tool
Bass: 4
Mid: 4
Treble: 8
Gain: 7.5

Testament
Bass- 6-7
Mids- 2-3
Treble- 4
Presence- 7-8
Gain- 5-7

John 5
Gain- 3-5
Bass-10
Mids-4
Treble- 8

Savatage
Gain 9
Treb 6
Mid 2
Bass 5
Presence 6

Thurston Moore of Sonic Youth
Gain 6
Treble 8
Mid 3-4
Bass 6

Radiohead - My Iron Lung
Drive: 10
Treble: 6
Middle: 7
Bass: 6
Reverb: 3

Herman Li of Dragonforce
gain- 10
bass- 8
mid- 5
treble 7

Yngwie Malmsteen
Bass 5-7
Mid 2-5
Treble 6-8
Presence 4-6
Volume 10

Paul Gilbert of Racer-X
Gain 7
Bass 7
Mid 5
Treble 7

Misery Signals
Distortion channel
gain-5
bass-6
mid-5
treble-6
resonance-5
presence-6

clean
gain-2 or 3
bass-8
mid-5
treble-4
resonance-8
presence-3

Norma Jean
gain:7-8
bass:7
mid:4
treble:6

Queens Of The Stone Age
Gain: 7
Treble: 3
Mid: 8
Bass: 6
Reverb: 0

George Thorogood
Drive: 6.5
Bass: 2.5
Mids: 7
Treble: 8
Chan. Vol.: 7.5

Slash of Velvet Revolver
Gain: 5-7
Treble: 4-6
Mid: 7-8
Bass: 6-8

Hello,

is there a solution for a better adjusting the Master Volume of the Code 50 . Actually i turn the Master Volume to 1, if i turn it up to 1.4 it's too loud. I don't want to adjust the PreAmp Volume, cause it will change the tone. I want to adjust the overall sound with the Master Volume and keep all the tone settings, no matter if i play at home or with the band. I also read the article "CODE 50 Master Volume Issue " from 26.Oct.2016. Is there a solution in the meantime?

Regards
Wolfgang

I just bought a code 50, downloaded the gateway app and tried to connect it to my galaxy note8.  I find that the app connects my note8 to the amp as an audio player (I can play songs in my note8's music library through the amp) but it will not connect the note8 to the amp as an amp controller.  In other words, I can play music through my amp but not control the amp's settings.  Even though the note8's bluetooth settings shows the amp is paired, the app says it's not connected.  I've followed the instructions found in the code 50 users manual as well as the instruction founs in the app itself several times to no avail.  Can you help please?  Thank you.

I was wondering if anyone has experienced this issue, I bought my CODE 100 brand new back in November and after about a week of having it, the sound began to mute in the middle of my playing for one  to two minutes. Turning the amp off and back on seems to be a temporary fix but the problem still occurs. I have also tried to see if there was a difference in having my CODE connected to the app, and it seems like the amp goes longer with keeping sound while connected to the app but it still mutes ocassionally. I also have the latestest firmware. 

Hi guys,

This isn't really a question but a solution to your problems connecting the Code to Studio One for USB recording. I got it to work using ASIO4All.

Here is a quick 2 minute video I made showing how: https://www.youtube.com/watch?v=LC1FAeFyRn8&feature=youtu.be

Marshall, feel free to point people here if they need this solution. Presonus just points them back to you.

David

Hello Team,

I just bought the Marshall Code25 and tried to update the Firmware via USB.

I have launched the firmware update from the Chrome Navigator and from Windows firmware application. After update performed, Code25 remains to version 1.11 and firmware indicates my CODE firmware is up to date. 

I have notice during the update than first, the version 1.41 is installed (MCU firmware 1.41) and just after a second update is launched installing the version 1.11 (DSP firmware 1.11)

Is it the regular behavior ?

After the update I still have troubles on bluethooth pairing, even if I read this problem should be solved by the update.

Thanks for your help

Regards

How Can I Program the Tuner on CODE Foot Controller? Thanks!

Hello Marshall Team,

i figured out following:

If code25 is in pairing mode (pressing REV/POWER),  you can see that code25 sends a device name ( something like "CODE V02004FA6E") within BT message to phone and phone asks for pairing, all works ok.

after switching power off and on again on code25, code25 sends again BT message but without device name, I guess the phone can't compare the device and thats why the paired connection can't be re-established from phone.

I checked this with BluetoothView v1.66 from NirSoft with win10.

best regards,

Peter

Is there any design modification being considered that would have a POWER LEVEL control added to any of the CODE amplifiers?

I am finding it difficult to get the level I want to suit different situations, such as studio, personal practice, session practice, etc., because of the sensitivity of the controls when using the amp at lower volumes.

My VOX has a power level control. It is very useful and allows me to use the other controls at the way I want to generate the tones and guitar response without overall volume issues.

Any comments...?

Just got a code 100 shipped to me today, opened it up pluged it in and no sound, plug headset in i get sound thru the headset but nowhere else, seams if i crank it i hear a faint sound from speakers tho, but otherwise any help ?

I'd really like the ability to roll back firmware updates.  The tone of this amp has got worse with each firmware update I've installed.  I wish I would have left it at the default when I got it.

The first firmware update I installed ruined the DSL, and 50's British amps, and now this last update has ruined everything else.  All the presets I created sound completely different now.  What a waste!

I'm really beginning to regret buying a digital amp.  

I recently bought the code 50 pedal and noticed that if I have the amp volume set to say 3 and then I hit one of the pedals to change to a different sound the volume changes...I need to figure this out quick as I have a gig coming up and this will obviously be a problem..thanks

Having trouble with the high noise floor of the Code series, and fizzy digital artifacts bubbling away in the background ?

Start with any of the 'Clean' preamps, and follow this article to the letter. It helps.

http://guitargearfinder.com/guides/ultimate-guide-to-guitar-amp-settings/

Please add firmware version number, date and release notes