Having this issue with Code 50 just updated the latest firmware 1.44v
The amp will hangs or store by itself and nothing works after operating for sometime.
Pressing the footswtich or amp buttons nothing works. Have to do a power reset on it.
Any idea what happen to this?
Hello !
I have a Code 50 and I use the Gateway to play, but it does'nt stay connected. For half an hour of playing, I have to reconnect 4-5 times. Do you know why ?
(The Code is the only Bluetooth connection in my phone).
Thank you !
JFG
Hello! Could I link the DI out of ori50h with an active speaker? Thanks
Hi,
I was wondering if I could plug in a two notes torpedo cab m into the 8 ohm speaker out jack of my Marshall Origin 20c without plugging it into the speaker as well? Would I need to put a dummy plug into the DI out to activate the built in load dummy load? Would the dummy load work without the dummy plug in the DI out? Can I even use the 8 ohm speaker out jack without a load on whatever I have plugged into it even with the DI out plugged into something? The two notes cab m does not have a dummy load built in and on normal amps would have to be plugged back into a speaker or a load box for the load and sound would still come out of the speaker.I'm wanting to use the two notes cab m so I can tweek cab imulations, record and use headphones all while still using my amp without disturbing anyone. I know I could just use the DI out, but I've read it alresady has cob imulation on it and I would like to tweek my own.
Hello,
I am a recent ower of a Marshall Origin 20, which I got in July. I've really enjoyed the amp until I plugged in last night and got out absolutely no sound out of it. I couldn't figure out why, as nothing as happened to it and it worked fine two days ago. I took it apart to do some trouble shooting and found that when I have all the knobs max'd and output on 20 watts, I can hear a whisper of my guitar signal (nicely saturated, presumably by the preamp tubes) through the speaker. This sound is affected by all of the knobs. However, if I plug my guitar directly into the return of the effects loop, and activate the effects loop I get no sound whatsoever; no guitar, no hum, nothing. Because of this, I'm sure my speaker is not the problem. These things led me to think it was a power amp section issue, so I went down and purchased a new set of matched EL34's, threw them in there, and nothing changed. I'd really like to know if there's anything I can do to fix this, because this amp is not even a year old and I should not be having these kinds of problems with completely normal bedroom use.
Thanks,
Alex
Hi There, My AS100D Channel 2 was working now is not working.
XLR Mic plug or Instrument mono jack.
I am looking for a more low ended sound than the provided 12 inch speaker cone and would like to try a 15 inch speaker cone. is it possible to do this with minimal or no modifications to the build of the amp?
Does anyone have a preset that is close to CC Deville of Poison?
Thanks
I'm attempting to discover a channel exchanging pedal for my DSL 100h. The Marshall site says it utilizes the PEDL-90012 which is out of creation. Can I simply utilize something like the MRPEDL91003 or do I have to get the first footswitch? tellthebell
I have a DSL 100h that has been fading in and out and crackling for quite some time. It seems to only happen on the clean channel and makes no difference, if I have my pedal board plugged in or not. I have the fx loop turned off, so I believe that that part of the circuit is out of the equation. I just swapped out the tubes because I suspected the pre amp tubes were bad from some other things I read and still no luck. Has anyone else experienced this?
Hi all. I have a Code 25 which sounds great through headphones using the cab emulation. Without headphones I'm struggling to find a cab that doesn't sound really boxy. If I switch the cab off, it becomes a fuzzy mess and is unusable. Am I missing something or is that just how it is?
Thanks in advance!
I know the origin 20 head has a dummy load for use without a cab and send to a daw through the di out. question is. Can I use the di out or fx send to a slave amp? Not a PA system but a 60 watt tube amp combo.
Hello,
I got a demo unit from a store and would like to know if I have to turn the Origin off before switching the output from low to/mid/high?
Thanks :D
Hi,
My Code 100 amp just dies off in the middle and comes back all of a sudden the volume just fades off for a while and it comes back at will. Even turning off the amp and on does not solve the issue but somehow after a while it becomes normal again. It seems to be some sort of a volume issue... When I crank the master volume knob to full , I hear faint sounds of my guitar. It comes back after a while automatically but then stops again at random.
Just bought a brand new Code 25 amp that was delivered by courier. It sounds great in play but there is a relatively loud constant hum from the speaker from about 5 seconds after switch on. Even with no guitar attached. is this normal?
Also something is rattling inside when I tilt the cabinet side to side. I'm worried it may have been damaged in transit. Maybe these two issues are related?
Anyone have any thoughts or advice. Not sure I can face sending it back to the seller as although I bought it off a .co.uk website it actually shipped from Poland.
On the Gateway app I can playback very little music. I can easily play music with iTunes (Bluetooth) but I am referring to using the playback feature. I have tried to playback 50-60 songs, some of it is purchased but all of it is downloaded. Why do only certain songs work. This is a huge issue for me and one of the main reasons I bought the Code 100H and 212 cabinet.
OD1 and OD2 getting terrible noise and squealing when Effects loop is engaged. I tried the Boss NS-2 in the loop and it had little effect on it. Loop pedals are TC Electronic Nova Delay, TC Electronic Chorus/flanger, Boss Digital Reverb, Boss NS-2 Noise Suppressor.
Outside the loop is Tuner, Volume pedal, BBE sonic stomp, Rockett Blue note, Wah pedal
I assume its a ground issue interference but no idea how to stop it.
When playing, randomly my code 50 will lose volume. I can restore the volume to normal levels by stepping on a button on the footswitch but then it will cut back out over and over. How do i fix this? Is there an update i can do? I have swapped the cable for the footswitch and my input. This is incredibly frustrating when trying to get through a rehersal session. Pleaae help!!!!!
Hi there,
after some time (months or weeks, I don't no) my Stanmore speaker plays from iPhone X very quietly. My iPhone is on maximum volume and Stanmore too. But my friends' devices play well. My iPhone plays well on other devices. Where is the problem? I can't find the solution.
Vlado