Good morning,
I have a code 50 (new, never used); the light on the LED button flashes without me touching anything, I have to press it so that it stops flashing (and therefore it lights up) and this for each preset selection. Can you tell me how to resolve the problem?
Thanks
Bonjour,
j'ai un code 50 (neuf, jamais servi) ; la lumière sur bouton DEL clignote sans que je ne touche à rien, il faut que j'appuie dessus pour qu'il arrête de clignoter (et donc il s'allume) et cela pour chaque sélection de preset. Pouvez vous me dire comment régler le problème ?
Merci
For the past week, I have noticed that my CODE 50 display will come on at full bright, but after 3 seconds it fades to a point where I can barely read it.
Is there a process that I can follow that will correct this?
Thanks!
Mark
When I try to connect my Marshall Code 25 to the computer, nothing works. I tried connecting it to my laptop but it was no use. I bought a wire yesterday that supports data transfer, can you tell me something?
I have a Marshall Code 50 with the 4 way footswitch. I have learned how to activate the various effects in switch mode, but I haven't found a solid volume adjustment workaround. For instance, if I am playing rhythm and need to go lead, I can activate a switch and go to distortion, but the level isn't adequate to drive the sound to the right volume for a lead guitar. I have tried adjusting the "level", but it won't go over the master level on the preamp volume-wise. Is there a "volume pedal" like solution for this? I am not sure if I can run a volume pedal in sequence with the footswitch, has anyone tried this?
Hello
I don't know if it has happened to anyone else.
The Marshall Code tuner is not very precise, having to resort to external tuners
I am having problems with the new firmware on my code 25 and gateway app on an iPhone. It used to work fine but now gateway is not connecting to the amp.
Hi, I have an issue where playing some notes in fifth octave like g5 weirdly resonates with some internals of the Amp amifying the note to unpleasant degree at the start of the note and even more couple of seconds later. Notes close to it behave normally.
This happens on both my guitars, both through the speaker and headphones on any cranked high gain Amp. My other two amps do not exhibit the same issue as well as boss gt-1000 connected to my code with ever section of it turned off.
Please help me troubleshoot this.
Obviously, I have updated to the latest firmware and did a factory reset after. However, neither of this helped.
I just bought the Marshall Code 25 Amplifier. Whenever I plug my guitar (Epiphone Les Paul Custom Replica), sometimes even just the cable into it, it makes a buzzing/ticking/crackle noise - sometimes both at the same time. When I play sound over Bluetooth or nothing is plugged into the "Input", it does not make the noise.
The guitar, plugged into a different amp (Cambridge Audio with Bose Sound System) with a different type of cable (RCA with a 6.3mm adapter at one end), also does not make the noise.
So either the amplifying circuit/chip in the code 25 is fried, or the cable (normal 6.3 on both ends) is.
Worth to note: the Guitar, Amp and the normal 6.3 cable are all brand new.
Do you know what can cause this and how to fix it, if the Amplifier is fried I can just return it within 2 years.
Могу ли я использовать наушники Bluetooth с усилителем Code 50, чтобы играть на гитаре и слушать ее? У меня есть Bluetooth-наушники, но они не работают...
Hello all
I am using a Code 25 together with a PEDL-91009 footswitch.
I would like to know if is it possible modify the volume using this pedal. I have read this thread:
(?
but it is not running, I am not getting different volume when changing the preset.
Your help is much appreciated ;-)
Kind regards,
Antonio R.
Please could Marshall and Softube create a new Amplifier with new effects and new improved amps and speaker Cab's..... Maybe call it... CODE-X....
or something like that...
I own three Marshall code's they are incredible.... Please I think Marshall and Softube are the best thing since Peanut and Jelly.... please continue this great pairing...
Thanks Allen Perez
allenperez911@yahoo.com
Just bought a code 50 amp, when traying it I noticed suddenly strange noises, so I unppluged the cable to ckeck if it was a problem with it and then noticed that the jack broke inside the amp. What is the sugested procedure in these situation? Can I open the back of the amp to remove the tip of the jack?
Is new, I don't want to lose the warranty.
Can I use the Code 100H as a pre-amp connected to a TSL 100?
Hello Marshall
I'm a beginner in guitar, and the code25 and my first amp, so happy !
but the front USB socket on the code25 leaves me with doubts about its solidity...
after 1 year of use my usb socket on code 25 no longer works, by plugging and unplugging so much, the connector is worn.
I of course changed the USB cable, and tried on another PC.
Is there a way to repair the USB connector? or change it?
thanks best regards for your support stef
With my phone, I have no problems at all connecting to my Code 50
I have an Android tablet that is very hit & miss connecting; at times, it will connect on first try. Other times, I have spent 25-30 minutes getting it to connect. I've gone as far as uninstalling Gateway and doing a fresh install.
Granted, it's a cheaper tablet but it shouldn't be this difficult
My footswitch is not working, just random flashing of different led sticks and numbers - no change from the current preset I'm in.
Is there a way to activate a factory reset of the switch?
I've just bought a Marshall CODE 50 and after playing a bit with it and experimenting around with the settings, I came to a conclusion that the cabinet models sound better recorded with the direct input than through the amp speaker when playing.
Just wondering if anyone thinks the same. Sorry if I couldn't make it more clear, English isn't my native language and I don't know how to fully express myself.
Hello-
Bought a second-hand CODE 50 and really love its flexibility when paired with the app.
I've tried recording by mic'ing it up with a SM57 but found the cabinet/speaker to be a little rattley and couldn't determine the source.
That led me to explore USB to DAW, unfortunately my brand new, and ten year old MacBooks both do not see the amp, and I cannot update thr Firmware via browser, per the instructions.
As a last ditch effort I went 1/8th" stereo cable out to L/R RCA with 1/4" adapters to get into my DAWs LINE-INs and pan hard left and right.
Works works great, but my question is - does the CODE 50 send a stereo signal from the headphone out? -and should I be running to hard panned inputs to capitalize on a stereo image?
Also, any remedy for connecting via USB to my MacBook to at least update the firmware?
Thx!
Installed the new firmware and now my Code 50 cuts out frequently and has to be restarted. It also seems to have effected the sound quality.
This needs to be fixed or post the old firmware version.
Thanks to Marshall for the latest firmware (v1.48) update and new presets. The eleven new presets are cool. Thanks again for keeping us Code amp owners in mind.
Kevin Towns